10 open source boards using the AD8418
Real designs built with the AD8418, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
MINI4
antonchromjak
65 × 18 mm151 parts4LNo license139STM32
Phobia
rombrew
82.6 × 55.3 mm165 parts8LCC-BY-SA-4.07STM32
VESC-6
veazhang
62 × 60 mm143 parts4LNo license4STM32
SPACE-DRIVE
msglazer
62 × 60 mm143 parts4LNo license1Isolated-Half-Bridge-Driver
CK20000
45 × 63.5 mm46 parts2LMIT1Elec Ventouse 2d
pollen-robotics
50 × 65 mm121 parts4LApache-2.00STM32
Mdrv
hanneskiene
60 × 50 mm112 parts4LMIT0STM32
MareapPowerBoard
RandBeyy
90 × 70 mm69 parts2LNo license0Mosfet switch
frawamudi
109.3 × 63.9 mm64 parts2LNo license0TMC6100-EVAL v1.2
opme
55 × 85 mm59 parts4LNo license0
How designs wire the AD8418
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the AD8418 connects to, and the resistors, capacitors and other passives placed on it.
- The IN- pin has a series resistor on 8 of 10 designs, most often 500 µΩ (then 10 Ω).
- The OUT pin has a series resistor on 8 of 10 designs, most often 100 Ω (then 1 kΩ).
- The VS pin has a decoupling capacitor on 8 of 10 designs, most often 2.2 µF (then 100 nF).
- The IN+ pin has a series resistor on 8 of 10 designs, most often 500 µΩ (then 25.5 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IN-pin 1 | Connected to: A connector 20% · BAT_OUT 20% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| REF2pin 3 | Connected to: GND 90% | — |
| NCpin 4 | Connected to: Not connected 100% | — |
| OUTpin 5 | Connected to: Signal 100% |
|
| VSpin 6 | Connected to: 3.3V 90% |
|
| REF1pin 7 | Connected to: 3.3V 80% | — |
| IN+pin 8 | Connected to: TMC6100-LA 20% · BAT_MOS_OUT 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MINI4 by antonchromjak, Phobia pcb by rombrew, VESC-6 by veazhang and Isolated-Half-Bridge-Driver by CK20000.
The AD8418 in open source designs
The gallery holds 10 open source boards using the AD8418 from 10 GitHub repositories; a typical one measures about 62 × 61.7 mm and carries around 117 components.
70% use four copper layers or more, and 40% carry an open source license.
The most starred is MINI4 by antonchromjak.
Parts used alongside the AD8418
Microcontrollers on boards using the AD8418
What boards using the AD8418 are built for
AD8418: common questions
Where can I find a AD8418 reference design?
Each of the 10 boards on this page is a real design using the AD8418. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the AD8418 IN- pin?
The IN- pin has a series resistor on 8 of 10 designs, most often 500 µΩ (then 10 Ω). Counted from the KiCad layouts of 10 open source designs using the AD8418.
What resistor goes on the AD8418 OUT pin?
The OUT pin has a series resistor on 8 of 10 designs, most often 100 Ω (then 1 kΩ). Counted from the KiCad layouts of 10 open source designs using the AD8418.
What decoupling capacitors do designs use on the AD8418 VS pin?
The VS pin has a decoupling capacitor on 8 of 10 designs, most often 2.2 µF (then 100 nF). Counted from the KiCad layouts of 10 open source designs using the AD8418.
What parts are used alongside the AD8418?
The STM32F40X_LQFP64, DRV8301, LM3671, MPU9250 and nRF24L01P appear in the most repositories here.
Which microcontrollers do boards using the AD8418 use?
Most are built on STM32 (6).
How big is a typical board using the AD8418?
The median is 62 × 61.7 mm, and 30% are two-layer designs.
What is the most popular open source board using the AD8418?
By GitHub stars, MINI4 by antonchromjak, with 139 stars.
Can I simulate one of these boards using the AD8418 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.