8 open source boards using the LM3671
Real designs built with the LM3671, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
TinyTracker
daveshah1
38 × 16 mm65 parts4LMIT13NXP
Runner s-GPS
dbtayl
79.9 × 50.8 mm38 parts2LBSD-3-Clause11ESP32
ESP32N1
whitecatboard
78 × 26 mm53 parts4LNo license9STM32
VESC-6
veazhang
62 × 60 mm143 parts4LNo license4STM32
SPACE-DRIVE
msglazer
62 × 60 mm143 parts4LNo license1ESP8266
Neatboard esp8266
galjonsfigur
28 × 34.2 mm49 parts2LMIT1PIC
Pic32devbrd
irwineffect
21.6 × 40 mm33 parts2LGPL-3.00STM32
RFMote PA
vedderb
64 × 27 mm73 parts4LGPL-3.0145
How designs wire the LM3671
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LM3671 connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a decoupling capacitor on 8 of 8 designs, most often 4.7 µF (then 2.2 µF).
- The SW pin has a inductor on 8 of 8 designs, most often 2.2 µH (then 74.5 GH).
- The FB pin has a inductor on 7 of 8 designs, most often 2.2 µH.
- The FB pin is tied to VCC on 7 of 8 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 5V 88% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| ENpin 3 | Connected to: 5V 75% · a signal 25% | — |
| FBpin 4 | Connected to: VCC 88% |
|
| SWpin 5 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RFMote PA by vedderb, TinyTracker by daveshah1, Runner s-GPS by dbtayl and ESP32N1 by whitecatboard.
The LM3671 in open source designs
The gallery holds 8 open source boards using the LM3671 from 8 GitHub repositories; a typical one measures about 62 × 37.1 mm and carries around 59 components.
63% use four copper layers or more, and 63% carry an open source license.
The most starred is RFMote PA by vedderb.
Parts used alongside the LM3671
What boards using the LM3671 are built for
LM3671: common questions
Where can I find a LM3671 reference design?
Each of the 8 boards on this page is a real design using the LM3671. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LM3671 VIN pin?
The VIN pin has a decoupling capacitor on 8 of 8 designs, most often 4.7 µF (then 2.2 µF). Counted from the KiCad layouts of 8 open source designs using the LM3671.
How is the LM3671 SW pin connected?
The SW pin has a inductor on 8 of 8 designs, most often 2.2 µH (then 74.5 GH). Counted from the KiCad layouts of 8 open source designs using the LM3671.
How is the LM3671 FB pin connected?
The FB pin has a inductor on 7 of 8 designs, most often 2.2 µH. Counted from the KiCad layouts of 8 open source designs using the LM3671.
What parts are used alongside the LM3671?
The STM32F40X_LQFP64, AD8418, DRV8301, MPU9250 and nRF24L01P appear in the most repositories here.
Which microcontrollers do boards using the LM3671 use?
Most are built on STM32 (4), ESP32 (1), ESP8266 (1) and NXP (1).
How big is a typical board using the LM3671?
The median is 62 × 37.1 mm, and 38% are two-layer designs.
What is the most popular open source board using the LM3671?
By GitHub stars, RFMote PA by vedderb, with 145 stars.
Can I simulate one of these boards using the LM3671 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.