15 open source boards using the ADS1015
Real designs built with the ADS1015, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Charge Controller
jharvey
139.7 × 88.9 mm157 parts2LNo license2496boards robomezzi
mwelling
85 × 54 mm112 parts4LCC-BY-SA-4.06FPGA
Eth4k hardware
theta-machines
98 × 58 mm132 parts4LCERN-OHL-W-2.04- schematic only · 99 partsAVR/Arduino
Bill-Of-Materials-Tools
Jesse-Millwood
99 partsNo license1 Artanis
aep
60 × 101 mm97 parts2LNo license0RP2040/RP2350
Mini-MIDI-Magic
arghya-v
250 × 116 mm49 parts2LNo license0Octelehat
imrehg
65 × 56 mm29 parts2LNo license0ESP32N1DEVKIT
whitecatboard
94 × 78.7 mm50 parts2LNo license9RP2040/RP2350
MIDI Board
Mithilessh2010
250 × 116 mm49 parts2LNo license0High torque servo arm remote
akornsys-rdi
100 × 64 mm29 parts2LGPL-3.00ESP32
SLAVE TEMP
zen451019
90 × 85 mm22 parts2LNo license1ESP32
SLAVE PRESSURE
zen451019
90 × 85 mm21 parts2LNo license1ESP32
SLAVE V-C INSOLATED
zen451019
90 × 85 mm19 parts2LNo license1ESP32
SLAVE V-C NO INSOLATED
zen451019
90 × 85 mm17 parts2LNo license1FeatherVoltmeterPCBA
oihdesigns
23.5 × 51.1 mm28 parts4LNo license2
How designs wire the ADS1015
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the ADS1015 connects to, and the resistors, capacitors and other passives placed on it.
- The ADDR pin is tied to GND on 8 of 11 designs (a signal on 2).
- The VDD pin has a decoupling capacitor on 6 of 11 designs, most often 100 nF (then 4.7 µF).
- The AIN1 pin has a series resistor on 5 of 11 designs, most often 47 kΩ (then 499 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADDRpin 1 | Connected to: GND 73% · a signal 18% | — |
| GNDpin 3 | Connected to: GND 91% | — |
| AIN1pin 5 | Connected to: A connector 27% · not connected 18% |
|
| VDDpin 8 | Connected to: 3.3V 82% · a signal 18% |
|
| SDApin 9 | Connected to: A connector 36%, the microcontroller 36% |
|
| SCLpin 10 | Connected to: A connector 36%, the microcontroller 36% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Charge Controller by jharvey, ESP32N1DEVKIT by whitecatboard, 96boards robomezzi by mwelling and Eth4k hardware by theta-machines.
The ADS1015 in open source designs
The gallery holds 15 open source boards using the ADS1015 from 12 GitHub repositories; a typical one measures about 90 × 85 mm and carries around 49 components.
79% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Charge Controller by jharvey.
Parts used alongside the ADS1015
Microcontrollers on boards using the ADS1015
What boards using the ADS1015 are built for
ADS1015: common questions
Where can I find a ADS1015 reference design?
Each of the 15 boards on this page is a real design using the ADS1015. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ADS1015 ADDR pin connected?
The ADDR pin is tied to GND on 8 of 11 designs (a signal on 2). Counted from the KiCad layouts of 11 open source designs using the ADS1015.
What decoupling capacitors do designs use on the ADS1015 VDD pin?
The VDD pin has a decoupling capacitor on 6 of 11 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 11 open source designs using the ADS1015.
What resistor goes on the ADS1015 AIN1 pin?
The AIN1 pin has a series resistor on 5 of 11 designs, most often 47 kΩ (then 499 kΩ). Counted from the KiCad layouts of 11 open source designs using the ADS1015.
What parts are used alongside the ADS1015?
The FT230X, Orpheus_Pico and PCM5100 appear in the most repositories here.
Which microcontrollers do boards using the ADS1015 use?
Most are built on ESP32 (5), RP2040/RP2350 (2), AVR/Arduino (1) and FPGA (1).
How big is a typical board using the ADS1015?
The median is 90 × 85 mm, and 79% are two-layer designs.
What is the most popular open source board using the ADS1015?
By GitHub stars, Charge Controller by jharvey, with 24 stars.
Can I simulate one of these boards using the ADS1015 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.