9 open source boards using the Arduino_UNO_R2

Real designs built with the Arduino_UNO_R2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the Arduino_UNO_R2

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the Arduino_UNO_R2 connects to, and the resistors, capacitors and other passives placed on it.

  • The IOREF pin is left unconnected on 7 of 7 designs.
  • The RESET pin is left unconnected on 7 of 7 designs.
  • The AREF pin is left unconnected on 7 of 7 designs.
  • The 3V3 pin is left unconnected on 6 of 7 designs.
NCpin 1Connected to: Not connected 100%
IOREFpin 2Connected to: Not connected 100%
RESETpin 3Connected to: Not connected 100%
3V3pin 4Connected to: Not connected 86%
GNDpin 6, 7, 29Connected to: GND 71% · a signal 24%
A0pin 9Connected to: Not connected 71% · a signal 29%
A1pin 10Connected to: Not connected 71% · a signal 29%
A2pin 11Connected to: Signal 57% · not connected 43%
  • Resistor to GND on 43% · 10 MΩ (1), 1 kΩ (1), 10 kΩ (1)
A3pin 12Connected to: Not connected 86%
D0/RXpin 15Connected to: Not connected 86%
D1/TXpin 16Connected to: Not connected 86%
D3pin 18Connected to: Signal 71% · not connected 29%
  • Series resistor on 43% · 10 kΩ (1), 220 Ω (1), 1 kΩ (1)
D4pin 19Connected to: Signal 86%
  • Series resistor on 43% · 10 kΩ (1), 1 kΩ (1)
D12pin 27Connected to: Not connected 71% · a signal 29%
AREFpin 30Connected to: Not connected 100%

13 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Teensy display shield by AnthonyDiGirolamo, Arduino by bmo00, MyIOShield by mwwhited and Arduino uno pet puller by sh123.

The Arduino_UNO_R2 in open source designs

The gallery holds 9 open source boards using the Arduino_UNO_R2 from 9 GitHub repositories; a typical one measures about 75.1 × 63.1 mm and carries around 20 components.

88% are two-layer designs, the rest use four layers or more, and 56% carry an open source license.

The most starred is OpenTheremin V3 Shield by GaudiLabs.

Microcontrollers on boards using the Arduino_UNO_R2

Arduino_UNO_R2: common questions

Where can I find a Arduino_UNO_R2 reference design?

Each of the 9 boards on this page is a real design using the Arduino_UNO_R2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the Arduino_UNO_R2 IOREF pin connected?

The IOREF pin is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the Arduino_UNO_R2.

How is the Arduino_UNO_R2 RESET pin connected?

The RESET pin is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the Arduino_UNO_R2.

How is the Arduino_UNO_R2 AREF pin connected?

The AREF pin is left unconnected on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the Arduino_UNO_R2.

Which microcontrollers do boards using the Arduino_UNO_R2 use?

Most are built on AVR/Arduino (8) and NXP (1).

How big is a typical board using the Arduino_UNO_R2?

The median is 75.1 × 63.1 mm, and 88% are two-layer designs.

What is the most popular open source board using the Arduino_UNO_R2?

By GitHub stars, OpenTheremin V3 Shield by GaudiLabs, with 45 stars.

Can I simulate one of these boards using the Arduino_UNO_R2 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part