10 open source boards using the ArduinoProMini
Real designs built with the ArduinoProMini, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
BOX-2252
fallberg
50.5 × 70 mm60 parts2LCERN-OHL-1.27AVR/Arduino
EasyPCB 10 nrf24l01p
sundberg84
50 × 49.9 mm30 parts2LNo license5ESP8266
SHMod24
LeoDJ
49.5 × 49.5 mm64 parts2LMIT3AVR/Arduino
Tachometer
PotatoX
78.6 × 60.8 mm48 parts2LCC-BY-NC-4.01AVR/Arduino
ArduinoIRstepperController
matt199394
45 × 94 mm17 parts2LNo license0AVR/Arduino
LE-BOX-0028
fallberg
76 × 96 mm60 parts2LCERN-OHL-1.27AVR/Arduino
EasyPCB 10 nrf24l01pbackupremove
sundberg84
50 × 49.9 mm30 parts2LNo license5AVR/Arduino
Tachometer Rev A
PotatoX
78.6 × 60.8 mm37 parts2LCC-BY-NC-4.01AVR/Arduino
MySensorsNode
fallberg
50 × 50 mm58 parts2LCERN-OHL-1.27AVR/Arduino
EasyPCB 10 RFM69hw
sundberg84
50 × 49.9 mm30 parts2LNo license5
How designs wire the ArduinoProMini
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ArduinoProMini connects to, and the resistors, capacitors and other passives placed on it.
- The ADC6/A6 pin is left unconnected on 4 of 5 designs.
- The ADC7/A7 pin is left unconnected on 4 of 5 designs.
- The (PCINT19/OC2B/INT1/PWM)P pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ (then 150 Ω).
- The (PCINT0/CLKO/ICP1)PB0/8 pin has a pull-up to 3.3V on 2 of 4 designs, most often 56 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 4, 23, 29 | Connected to: GND 93% | — |
| (PCINT19/OC2B/INT1/PWM)Ppin 6 | Connected to: A connector 80% |
|
| (PCINT0/CLKO/ICP1)PB0/8pin 11 | Connected to: AT25DF512C 50% |
|
| (PCINT8/ADC0)PC0/14/A0pin 17 | Connected to: A connector 75% · VBAT_SMPL 25% |
|
| (PCINT11/ADC3)PC3/17/A3pin 20 | Connected to: ATSHA204A 50%, a connector 50% |
|
| VCCpin 21 | Connected to: 3.3V 100% | — |
| (PCINT12/SDA/ADC4)PC4/18pin 25 | Connected to: A connector 80% |
|
| (PCINT13/SCL/ADC5)PC5/19pin 26 | Connected to: A connector 80% |
|
| ADC6/A6pin 27 | Connected to: Not connected 80% · a signal 20% | — |
| ADC7/A7pin 28 | Connected to: Not connected 80% · a signal 20% | — |
16 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MySensorsNode by fallberg, EasyPCB 10 nrf24l01p by sundberg84, SHMod24 by LeoDJ and Tachometer by PotatoX.
The ArduinoProMini in open source designs
The gallery holds 10 open source boards using the ArduinoProMini from 5 GitHub repositories; a typical one measures about 50 × 55.4 mm and carries around 43 components.
100% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is LE-BOX-0028 by fallberg.
Parts used alongside the ArduinoProMini
Microcontrollers on boards using the ArduinoProMini
What boards using the ArduinoProMini are built for
ArduinoProMini: common questions
Where can I find a ArduinoProMini reference design?
Each of the 10 boards on this page is a real design using the ArduinoProMini. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ArduinoProMini ADC6/A6 pin connected?
The ADC6/A6 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ArduinoProMini.
How is the ArduinoProMini ADC7/A7 pin connected?
The ADC7/A7 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ArduinoProMini.
What pull-up resistor is used on the ArduinoProMini (PCINT19/OC2B/INT1/PWM)P pin?
The (PCINT19/OC2B/INT1/PWM)P pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ (then 150 Ω). Counted from the KiCad layouts of 5 open source designs using the ArduinoProMini.
What parts are used alongside the ArduinoProMini?
The NRF24L01, AT25DF512C, ATSHA204A and RFM69HW appear in the most repositories here.
Which microcontrollers do boards using the ArduinoProMini use?
Most are built on AVR/Arduino (9) and ESP8266 (1).
How big is a typical board using the ArduinoProMini?
The median is 50 × 55.4 mm, and 100% are two-layer designs.
What is the most popular open source board using the ArduinoProMini?
By GitHub stars, LE-BOX-0028 by fallberg, with 7 stars.
Can I simulate one of these boards using the ArduinoProMini before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.