21 open source boards using the ATmega2560-16A

Real designs built with the ATmega2560-16A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the ATmega2560-16A

Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the ATmega2560-16A connects to, and the resistors, capacitors and other passives placed on it.

  • The RESET pin has a pull-up to 5V on 11 of 13 designs, most often 10 kΩ (then 12 kΩ).
  • The PH7 pin is left unconnected on 13 of 14 designs.
  • The PG3 pin is left unconnected on 13 of 14 designs.
  • The PE2 pin is left unconnected on 12 of 14 designs (a signal on 2).
PE2pin 4Connected to: Not connected 86%
PE6pin 8Connected to: Not connected 79% · a signal 21%
PE7pin 9Connected to: Not connected 79% · a signal 21%
VCCpin 10, 31, 61, 80Connected to: 5V 98%
  • Decoupling capacitor on 57% · 100 nF (21), 22 µF (3), 10 nF (2)
GNDpin 11, 32, 62, 81, 99Connected to: GND 98%
PH0pin 12Connected to: Not connected 64% · a signal 36%
PH2pin 14Connected to: Not connected 86%
PB0pin 19Connected to: Not connected 71% · a signal 29%
PH7pin 27Connected to: Not connected 93%
PG3pin 28Connected to: Not connected 93%
PG4pin 29Connected to: Not connected 92%
RESETpin 30Connected to: A connector 85%
  • Pull-up to 5V on 85% · 10 kΩ (9), 12 kΩ (1)
  • Series capacitor on 38% · 100 nF (3), 1 µF (1)
  • Capacitor to GND on 31% · 22 pF (2), 100 nF (1)
XTAL2pin 33Connected to: Signal 100%
  • Crystal on 77% · 16 MHz (5)
  • Capacitor to GND on 77% · 22 pF (3), 12 pF (1), 100 nF (1)
  • Series resistor on 31% · 1 MΩ (4)
XTAL1pin 34Connected to: Signal 100%
  • Crystal on 77% · 16 MHz (5)
  • Capacitor to GND on 77% · 22 pF (3), 12 pF (1), 100 nF (1)
  • Series resistor on 31% · 1 MΩ (3), 27 Ω (1)
PL0pin 35Connected to: Not connected 62% · a signal 38%
PL1pin 36Connected to: Not connected 62% · a signal 38%
PL2pin 37Connected to: Not connected 62% · a signal 38%
PL3pin 38Connected to: Not connected 62% · a signal 38%
PL6pin 41Connected to: Not connected 62% · a signal 38%
PL7pin 42Connected to: Not connected 62% · a signal 38%
PD0pin 43Connected to: A connector 38% · not connected 38%
  • Pull-up to 5V on 31% · 10 kΩ (3), 4.7 kΩ (1)
PD1pin 44Connected to: A connector 38% · not connected 38%
  • Pull-up to 5V on 31% · 10 kΩ (3), 4.7 kΩ (1)
PD4pin 47Connected to: Not connected 85% · a signal 15%
PD5pin 48Connected to: Not connected 85% · a signal 15%
PD6pin 49Connected to: Not connected 77% · a signal 23%
PD7pin 50Connected to: Not connected 62% · a signal 38%
PG0pin 51Connected to: Not connected 69% · a signal 31%
PG1pin 52Connected to: Not connected 69% · a signal 31%
PJ2pin 65Connected to: Not connected 92%
PJ3pin 66Connected to: Not connected 85% · a signal 15%
PJ4pin 67Connected to: Not connected 85% · a signal 15%
PJ5pin 68Connected to: Not connected 85% · a signal 15%
PJ6pin 69Connected to: Not connected 85% · a signal 15%
PG2pin 70Connected to: Not connected 62% · a signal 38%
PA4pin 74Connected to: Not connected 62% · a signal 38%
PJ7pin 79Connected to: Not connected 92%
PK7pin 82Connected to: Not connected 62% · a signal 38%
AREFpin 98Connected to: A connector 23% · not connected 38%
  • Capacitor to GND on 46% · 100 nF (4)
AVCCpin 100Connected to: 5V 92%
  • Decoupling capacitor on 54% · 100 nF (7), 10 nF (1)

54 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Main by LouiseLeciak, LaunchController by tokai-student-rocket-project, Line V7 ATmega2560 by Gamu2124 and Arduino by odobot.

The ATmega2560-16A in open source designs

The gallery holds 21 open source boards using the ATmega2560-16A from 15 GitHub repositories; a typical one measures about 120.8 × 100 mm and carries around 94 components.

57% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.

The most starred is Main by LouiseLeciak.

Microcontrollers on boards using the ATmega2560-16A

ATmega2560-16A: common questions

Where can I find a ATmega2560-16A reference design?

Each of the 21 boards on this page is a real design using the ATmega2560-16A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ATmega2560-16A RESET pin?

The RESET pin has a pull-up to 5V on 11 of 13 designs, most often 10 kΩ (then 12 kΩ). Counted from the KiCad layouts of 14 open source designs using the ATmega2560-16A.

How is the ATmega2560-16A PH7 pin connected?

The PH7 pin is left unconnected on 13 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the ATmega2560-16A.

How is the ATmega2560-16A PG3 pin connected?

The PG3 pin is left unconnected on 13 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the ATmega2560-16A.

What parts are used alongside the ATmega2560-16A?

The CH340C, USBLC6-2SC6, AMS1117-3.3, ATmega16U2-M and USBLC6-4SC6 appear in the most repositories here.

Which microcontrollers do boards using the ATmega2560-16A use?

Most are built on AVR/Arduino (17) and ESP32 (4).

How big is a typical board using the ATmega2560-16A?

The median is 120.8 × 100 mm, and 57% are two-layer designs.

What is the most popular open source board using the ATmega2560-16A?

By GitHub stars, Main by LouiseLeciak, with 3 stars.

Can I simulate one of these boards using the ATmega2560-16A before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part