9 open source boards using the BQ24073RGTR
Real designs built with the BQ24073RGTR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Phoniesp32
butzist
57.4 × 50 mm55 parts4LMIT11ESP32
Phone board
JamesTwallin
60 × 33 mm62 parts4LMIT6ESP32
Hoerbaer
drachosaurus
76 × 88 mm195 parts4LNo license1STM32
Stm32-epaper
Mlynn217
97.4 × 60 mm142 parts4LNo license1Raspberry Pi
Kids timer
jnd-cz
150 × 150 mm266 parts2LNo license0ESP32
Waypoint
M-Mrk
140 × 80 mm129 parts4LNo license0ESP32
Mobile-PCB-Files-
sumit123hub
128.7 × 60.3 mm92 parts2LNo license0STM32
DRP.004
MuffinKing-jpeg
42 × 27 mm59 parts4LNo license0ESP32
Phone board mems
JamesTwallin
55 × 31 mm58 parts4LMIT6
How designs wire the BQ24073RGTR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the BQ24073RGTR connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM_12 pin has a resistor to GND on 8 of 8 designs, most often 1.5 kΩ (then 1.2 kΩ).
- The BAT_2 pin is tied to BATT on 8 of 8 designs.
- The BAT_3 pin is tied to BATT on 8 of 8 designs.
- The TS_1 pin has a resistor to GND on 6 of 8 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| TS_1pin 1 | Connected to: A connector 25% |
|
| BAT_2pin 2 | Connected to: BATT 100% |
|
| BAT_3pin 3 | Connected to: BATT 100% |
|
| CE_4pin 4 | Connected to: GND 75% · a signal 25% | — |
| EN1_6pin 6 | Connected to: Signal 63% · GND 25% |
|
| PGOOD_7pin 7 | Connected to: The microcontroller 38% |
|
| VSS_8pin 8 | Connected to: GND 100% | — |
| OUT_10pin 10 | Connected to: VSYS 75% · a signal 25% | — |
| OUT_11pin 11 | Connected to: VSYS 75% · a signal 25% | — |
| ILIM_12pin 12 | Connected to: Signal 100% |
|
| IN_13pin 13 | Connected to: VBUS 88% | — |
| TMR_14pin 14 | Connected to: Signal 63% · not connected 38% |
|
| ISET_16pin 16 | Connected to: Signal 100% |
|
| EP_17pin 17 | Connected to: GND 100% | — |
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Phoniesp32 by butzist, Phone board by JamesTwallin, Hoerbaer by drachosaurus and Stm32-epaper by Mlynn217.
The BQ24073RGTR in open source designs
The gallery holds 9 open source boards using the BQ24073RGTR from 8 GitHub repositories; a typical one measures about 76 × 60 mm and carries around 92 components.
78% use four copper layers or more, and 33% carry an open source license.
The most starred is Phoniesp32 by butzist.
Parts used alongside the BQ24073RGTR
Microcontrollers on boards using the BQ24073RGTR
What boards using the BQ24073RGTR are built for
BQ24073RGTR: common questions
Where can I find a BQ24073RGTR reference design?
Each of the 9 boards on this page is a real design using the BQ24073RGTR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the BQ24073RGTR ILIM_12 pin?
The ILIM_12 pin has a resistor to GND on 8 of 8 designs, most often 1.5 kΩ (then 1.2 kΩ). Counted from the KiCad layouts of 8 open source designs using the BQ24073RGTR.
How is the BQ24073RGTR BAT_2 pin connected?
The BAT_2 pin is tied to BATT on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the BQ24073RGTR.
How is the BQ24073RGTR BAT_3 pin connected?
The BAT_3 pin is tied to BATT on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the BQ24073RGTR.
Which microcontrollers do boards using the BQ24073RGTR use?
Most are built on ESP32 (6), STM32 (2) and Raspberry Pi (1).
How big is a typical board using the BQ24073RGTR?
The median is 76 × 60 mm, and 22% are two-layer designs.
What is the most popular open source board using the BQ24073RGTR?
By GitHub stars, Phoniesp32 by butzist, with 11 stars.
Can I simulate one of these boards using the BQ24073RGTR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.