8 open source boards using the INA138
Real designs built with the INA138, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Sweep
waffle87
216.9 × 86.9 mm208 parts2LSHL-2.157PIC
QI Charger
drewsum
150 × 50 mm293 parts2LNo license20RP2040/RP2350
Raii
unspecworks
236.9 × 86.9 mm208 parts2LSHL-2.117AVR/Arduino
Power Supply
adsehgal
100 × 50 mm94 parts2LNo license2STM32
Robotont electronics mainboard
robotont
304.3 × 274 mm407 parts2LNo license1STM32
Svelotracker
SL-RU
98.6 × 49.8 mm102 parts2LNo license1RP2040/RP2350
UMMTJ Mainboard
vamatis
100 × 100 mm142 parts4LNo license0PIC
BBB SHIELD V2
vic-simkus
89.3 × 102.1 mm117 parts4LCERN-OHL-1.20
How designs wire the INA138
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the INA138 connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF (then 1 µF).
- Pin 1 has a resistor to GND on 5 of 7 designs, most often 499 kΩ (then 500 kΩ).
- The + pin has a pull-up to 5V on 4 of 7 designs, most often 5 mΩ (then 20 mΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 57% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| +pin 3 | Connected to: Signal 100% |
|
| V+pin 5 | Connected to: 5V 71% · a signal 29% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sweep by waffle87, QI Charger by drewsum, Raii by unspecworks and Power Supply by adsehgal.
The INA138 in open source designs
The gallery holds 8 open source boards using the INA138 from 8 GitHub repositories; a typical one measures about 125 × 86.9 mm and carries around 175 components.
75% are two-layer designs, the rest use four layers or more, and 13% carry an open source license.
The most starred is Sweep by waffle87.
Parts used alongside the INA138
Microcontrollers on boards using the INA138
What boards using the INA138 are built for
INA138: common questions
Where can I find a INA138 reference design?
Each of the 8 boards on this page is a real design using the INA138. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the INA138 V+ pin?
The V+ pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 7 open source designs using the INA138.
What resistor goes on the INA138 pin 1?
Pin 1 has a resistor to GND on 5 of 7 designs, most often 499 kΩ (then 500 kΩ). Counted from the KiCad layouts of 7 open source designs using the INA138.
What pull-up resistor is used on the INA138 + pin?
The + pin has a pull-up to 5V on 4 of 7 designs, most often 5 mΩ (then 20 mΩ). Counted from the KiCad layouts of 7 open source designs using the INA138.
What parts are used alongside the INA138?
The W25Q128JVS, 74LVC1G17, RP2040, SN74LVC1T45DRL and SRV05-4 appear in the most repositories here.
Which microcontrollers do boards using the INA138 use?
Most are built on RP2040/RP2350 (3), PIC (2), STM32 (2) and AVR/Arduino (1).
How big is a typical board using the INA138?
The median is 125 × 86.9 mm, and 75% are two-layer designs.
What is the most popular open source board using the INA138?
By GitHub stars, Sweep by waffle87, with 57 stars.
Can I simulate one of these boards using the INA138 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.