20 open source boards using the IR2101
Real designs built with the IR2101, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
RT-STACK
fupsrl
150 × 150 mm472 parts6LCC-BY-NC-4.015KiCad-Sensorless-BLDC-ESC
phpkadir
99.1 × 99.1 mm55 parts2LMIT2NXP
Bbesc
jakeread
110.5 × 82.6 mm79 parts2LNo license1Isolated-Half-Bridge-Driver
CK20000
45 × 63.5 mm46 parts2LMIT1- schematic only · 91 parts
SimpleBLDC32
techn0man1ac
91 partsMIT1 PIC
DCC-Booster
DavidMFlynn
102.9 × 99.1 mm118 parts2LGPL-3.00PlacaPotencia KONTEAM
Adbeor
170 × 98.5 mm79 parts2LNo license0RISC-V
Bidirectional tester
c3am
68 × 60 mm70 parts2LNo license0STM32
BLDCControl1.kicad Lolin32Lite sch
gyukiss55
157.5 × 109.2 mm45 parts2LNo license0- schematic only · 79 partsSTM32
HDD-Payload-ESC
Dsmannight
79 partsNo license0 Bldc drive
pekkaroi
98 × 50 mm49 parts2LGPL-2.0199STM32
XESC
embeddedalpha
38 × 54 mm93 parts2LMIT75NXP
Bbesc kiCad 1stAttempt
jakeread
59 parts2LNo license16NXP
Bbesc kiCad 1stAttempt
jakeread
59 parts2LNo license1BLDCControl1
gyukiss55
95.2 × 87.7 mm36 parts2LNo license0Alu casing
pekkaroi
98 × 90 mm49 parts2LGPL-2.0199AVR/Arduino
Wp controller
pypilot
75.1 × 50 mm77 parts4LNo license3AVR/Arduino
1dofcopter
ieee-cas-unmsm
94.9 × 88.4 mm52 parts2LNo license0AVR/Arduino
Wp controller box
pypilot
75.1 × 50 mm77 parts4LNo license3AVR/Arduino
Wp controller outline
pypilot
75.1 × 50 mm71 parts4LNo license3
How designs wire the IR2101
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the IR2101 connects to, and the resistors, capacitors and other passives placed on it.
- The LO pin has a series resistor on 13 of 13 designs, most often 10 Ω (then 100 Ω).
- The VS pin has a series capacitor on 13 of 13 designs, most often 100 nF (then 10 µF).
- The HO pin has a series resistor on 13 of 13 designs, most often 10 Ω (then 100 Ω).
- The VB pin has a series capacitor on 13 of 13 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 12V 85% · a signal 15% |
|
| COMpin 4 | Connected to: GND 100% | — |
| LOpin 5 | Connected to: Signal 100% |
|
| VSpin 6 | Connected to: A connector 46% |
|
| HOpin 7 | Connected to: Signal 100% |
|
| VBpin 8 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bldc drive by pekkaroi, XESC by embeddedalpha, Bbesc kiCad 1stAttempt by jakeread and RT-STACK by fupsrl.
The IR2101 in open source designs
The gallery holds 20 open source boards using the IR2101 from 15 GitHub repositories; a typical one measures about 96.6 × 85.1 mm and carries around 71 components.
78% are two-layer designs, the rest use four layers or more, and 35% carry an open source license.
The most starred is Alu casing by pekkaroi.
Parts used alongside the IR2101
Microcontrollers on boards using the IR2101
What boards using the IR2101 are built for
IR2101: common questions
Where can I find a IR2101 reference design?
Each of the 20 boards on this page is a real design using the IR2101. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the IR2101 LO pin?
The LO pin has a series resistor on 13 of 13 designs, most often 10 Ω (then 100 Ω). Counted from the KiCad layouts of 13 open source designs using the IR2101.
How is the IR2101 VS pin connected?
The VS pin has a series capacitor on 13 of 13 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 13 open source designs using the IR2101.
What resistor goes on the IR2101 HO pin?
The HO pin has a series resistor on 13 of 13 designs, most often 10 Ω (then 100 Ω). Counted from the KiCad layouts of 13 open source designs using the IR2101.
What parts are used alongside the IR2101?
The AMS1117-5.0, 6N137, AMS1117-3.3, L7805 and LM358N appear in the most repositories here.
Which microcontrollers do boards using the IR2101 use?
Most are built on AVR/Arduino (4), STM32 (4), NXP (3) and PIC (1).
How big is a typical board using the IR2101?
The median is 96.6 × 85.1 mm, and 78% are two-layer designs.
What is the most popular open source board using the IR2101?
By GitHub stars, Alu casing by pekkaroi, with 199 stars.
Can I simulate one of these boards using the IR2101 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.