58 open source boards using the 6N137
Real designs built with the 6N137, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NXP
TSynth Teensy 4.1
Electrotechnique
312 × 140 mm105 parts2LNo license180RP2040/RP2350
Cyclic
tpcarlson
241.2 × 160 mm437 parts4LNo license106ESP32
PCBA-KNOT
intechstudio
56 × 60 mm110 parts4LGPL-3.057Back
cristibaluta
135.2 × 115.3 mm26 parts2LCustom license52STM32
OTTO-Beta-Main
bitfieldaudio
288.5 × 95 mm303 parts4LCC-BY-NC-4.037AVR/Arduino
Polykit Kosmo Multitool
polykit
60 × 150 mm90 parts2LCC-BY-NC-4.031STM32
MidiMonger components
dchwebb
40 × 100 mm64 parts2LNo license12AVR/Arduino
Midi2gate
sebastianbeyer
74 × 175 mm75 parts2LNo license10Multi midi
ReflexCreations
101.2 × 71.1 mm59 parts2LMIT8PIC
YAPSCO-10V
simonjoh
82.8 × 73.2 mm72 parts2LGPL-3.07ESP32
GalvOS Laser Controller V2
Andre1Becker
175 × 115 mm122 parts2LGPL-3.05Tesla-Coil-MIDI-Synth
ucsbieee
132.1 × 61 mm94 parts4LNo license4MaD Edge
RileyMcCarthy
144.1 × 93.4 mm164 parts4LNo license3AVR/Arduino
Mls800
blemasle
293.4 × 80.5 mm92 parts2LGPL-3.03STM32
Audio daughterboard
Jaxc
90 × 155 mm453 parts4LGPL-3.02Ksoloti gills
ksoloti
150 × 92 mm206 parts2LCC-BY-4.02STM32
Light Commander
ethandrzb
70.2 × 108 mm163 parts6LNo license2Z80-SOUND
dennis9819
160 × 100.3 mm104 parts2LNo license2STM32
LaserHarp3 - V2
amonbenson
79.8 × 99.1 mm129 parts2LNo license1Isolated-Half-Bridge-Driver
CK20000
45 × 63.5 mm46 parts2LMIT1Midiskirt
barzamin
61.9 × 66.7 mm28 parts2LNo license1ESP32
12 Driver Board
617quan
381 × 304.8 mm209 parts4LNo license0AVR/Arduino
Digital synth
giacomogramaglia
165 × 90.1 mm135 parts2LNo license0FOC INVERTER
Abdelrahman-Elnahrawy
245.4 × 77.5 mm132 parts2LGPL-3.00PIC
DCC-Booster
DavidMFlynn
102.9 × 99.1 mm118 parts2LGPL-3.00Midi controller
petitechose-midi-studio
164 × 164 mm112 parts4LCERN-OHL-S-2.00Probador - Modulo Principal
Gonzalogontad
100 × 70 mm104 parts2LNo license0RP2040/RP2350
ALTERNANCIA PI PICO
zen451019
150 × 100 mm71 parts2LNo license0DCC-Turnout-4CH
tatuiot
77.7 × 66.2 mm57 parts2LNo license0AVR/Arduino
DMX2SGM
Gabse
66.5 × 90.9 mm32 parts2LCC-BY-NC-4.00AVR/Arduino
Beech215PropController
billmallard
100 × 80 mm27 parts2LMIT0ESP32
Bridge
nichtrami
131.8 × 51.8 mm14 parts2LApache-2.00- schematic only · 34 partsAVR/Arduino
Ay module
dnewcome
34 partsNo license0 RP2040/RP2350
Brain core
shmoergh
60.5 × 110 mm95 parts2LNo license219STM32
MidiMonger
dchwebb
40 × 110 mm56 parts2LNo license12MIDI IN Breakout Board
TuDo-Makerspace
20.3 × 62 mm9 parts2LNo license6
How designs wire the 6N137
Read from the KiCad layouts of 45 open source designs, one per repository: what each pin of the 6N137 connects to, and the resistors, capacitors and other passives placed on it.
- The A pin has a series resistor on 35 of 45 designs, most often 220 Ω (then 470 Ω).
- The VO pin has a pull-up to 5V on 34 of 45 designs, most often 10 kΩ (then 4.7 kΩ).
- The VCC pin has a decoupling capacitor on 23 of 45 designs, most often 100 nF (then 100 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 4 | Connected to: Not connected 94% | — |
| Apin 2 | Connected to: Signal 93% |
|
| GNDpin 5 | Connected to: GND 93% | — |
| VOpin 6 | Connected to: The microcontroller 40%, a connector 33% |
|
| VCCpin 8 | Connected to: 5V 87% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Brain core by shmoergh, TSynth Teensy 4.1 by Electrotechnique, Cyclic by tpcarlson and Booster-Link by GBert.
The 6N137 in open source designs
The gallery holds 58 open source boards using the 6N137 from 46 GitHub repositories; a typical one measures about 95 × 85 mm and carries around 67 components.
81% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Brain core by shmoergh.
Parts used alongside the 6N137
Microcontrollers on boards using the 6N137
What boards using the 6N137 are built for
6N137: common questions
Where can I find a 6N137 reference design?
Each of the 58 boards on this page is a real design using the 6N137. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 6N137 A pin?
The A pin has a series resistor on 35 of 45 designs, most often 220 Ω (then 470 Ω). Counted from the KiCad layouts of 45 open source designs using the 6N137.
What pull-up resistor is used on the 6N137 VO pin?
The VO pin has a pull-up to 5V on 34 of 45 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 45 open source designs using the 6N137.
What decoupling capacitors do designs use on the 6N137 VCC pin?
The VCC pin has a decoupling capacitor on 23 of 45 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 45 open source designs using the 6N137.
What parts are used alongside the 6N137?
The AMS1117-3.3, AMS1117-5.0, PC817, TL074 and 74HC595 appear in the most repositories here.
Which microcontrollers do boards using the 6N137 use?
Most are built on AVR/Arduino (14), ESP32 (9), STM32 (7) and PIC (4).
How big is a typical board using the 6N137?
The median is 95 × 85 mm, and 81% are two-layer designs.
What is the most popular open source board using the 6N137?
By GitHub stars, Brain core by shmoergh, with 219 stars.
Can I simulate one of these boards using the 6N137 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.