23 open source boards using the L7912
Real designs built with the L7912, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Eurorack psu
polykit
117 × 72 mm30 parts2LNo license37RP2040/RP2350
AWG
F6ITU
140 × 75 mm73 parts2LNo license14PSU linear reg
matterwaves
100 × 40 mm24 parts2LNo license1Eurorack-PSU
JacobParent7
108 × 44.5 mm15 parts2LNo license1OpticalAbsorptionMeasurement before
Johann-Schmid
166 × 160 mm159 parts2LNo license0Dac circ
b3dag
193 × 160 mm149 parts2LNo license0Analog audio visualizer
alimleahat
130 × 100 mm65 parts2LNo license0Bachelor thesis
dario0603
99 × 99 mm57 parts2LNo license03APSU
codesqueak
178 × 127 mm45 parts2LCERN-OHL-S-2.00Kicad trans pwr
s59mz
86.4 × 95.3 mm34 parts2LGPL-3.00Solar-Telescope-Redesign
RomiFC
128.3 × 45.7 mm22 parts2LNo license0GitHub2
NaraenderHardware
33.5 × 30 mm22 parts2LMIT0- schematic only · 84 partsESP32
Esp32-olcum karti
Muhammet933321
84 partsMIT0 WithElectronicPoti
Johann-Schmid
166 × 160 mm159 parts2LNo license0Psu linear reg
jc-roth
100 × 40 mm18 parts2LNo license0GradientDriver
xecus
54.6 × 68 mm57 parts4LNo license48OpticalAbsorptionMeasurement
Johann-Schmid
160 × 160 mm133 parts2LNo license0Power supply
b3dag
90.8 × 52.1 mm12 parts2LNo license0PSU
carl-becker
350 × 50 mm45 parts2LNo license0FC power
zero-emission
110 × 40 mm32 parts2LNo license14Power Supply THT
BruteClaw
200 × 120 mm49 parts2LGPL-3.010GIMIX Serial dumb
roberto314
132.4 × 88.4 mm47 parts2LBSD-2-Clause1Power supply
gridbugs
70 × 135 mm32 parts2LMIT0
How designs wire the L7912
Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the L7912 connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a capacitor to GND on 13 of 18 designs, most often 4.7 mF (then 2.2 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 89% | — |
| VIpin 2 | Connected to: A connector 22% · -15V 22% |
|
| VOpin 3 | Connected to: -12V 83% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GradientDriver by xecus, Eurorack psu by polykit, AWG by F6ITU and FC power by zero-emission.
The L7912 in open source designs
The gallery holds 23 open source boards using the L7912 from 20 GitHub repositories; a typical one measures about 122.6 × 81.7 mm and carries around 45 components.
95% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is GradientDriver by xecus.
Microcontrollers on boards using the L7912
What boards using the L7912 are built for
L7912: common questions
Where can I find a L7912 reference design?
Each of the 23 boards on this page is a real design using the L7912. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the L7912 VI pin connected?
The VI pin has a capacitor to GND on 13 of 18 designs, most often 4.7 mF (then 2.2 µF). Counted from the KiCad layouts of 18 open source designs using the L7912.
What parts are used alongside the L7912?
The L7812, L7805, L7905 and LM358 appear in the most repositories here.
Which microcontrollers do boards using the L7912 use?
Most are built on ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the L7912?
The median is 122.6 × 81.7 mm, and 95% are two-layer designs.
What is the most popular open source board using the L7912?
By GitHub stars, GradientDriver by xecus, with 48 stars.
Can I simulate one of these boards using the L7912 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.