7 open source boards using the LM6172
Real designs built with the LM6172, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Adcboard
nuclearfutureslab
184 × 80 mm124 parts2LGPL-3.05Adcboard
sgs-lab
184 × 80 mm124 parts2LNo license2AVR/Arduino
AVML: PCB1 & PCB2
joem
37.5 × 100 mm74 parts2LNo license0FGControl
odegroote
100 × 71 mm49 parts2LGPL-3.00AVR/Arduino
FNMES-Technical-Guide
ThemisEfth
58.5 × 44.2 mm31 parts2LMIT0Vga cpld jtag
scefrom
223.5 × 147.3 mm122 parts2LCustom license2Vga cpld
scefrom
223.5 × 147.3 mm116 parts2LCustom license2
How designs wire the LM6172
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LM6172 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 6 of 6 designs, most often 1 kΩ (then 20 kΩ).
- The - pins have a series resistor on 6 of 6 designs, most often 1 kΩ (then 20 kΩ).
- The + pins have a series resistor on 6 of 6 designs, most often 8.2 kΩ (then 1 kΩ).
- The V- pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: A connector 67% |
|
| -pin 2, 6 | Connected to: Signal 100% |
|
| +pin 3, 5 | Connected to: Signal 92% |
|
| V-pin 4 | Connected to: -12V 83% · a signal 17% |
|
| Pin 7 | Connected to: A connector 33% |
|
| V+pin 8 | Connected to: 12V 83% · a signal 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Adcboard by nuclearfutureslab, Vga cpld by scefrom, Adcboard by sgs-lab and AVML: PCB1 & PCB2 by joem.
The LM6172 in open source designs
The gallery holds 7 open source boards using the LM6172 from 6 GitHub repositories; a typical one measures about 184 × 80 mm and carries around 116 components.
100% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is Adcboard by nuclearfutureslab.
Parts used alongside the LM6172
Microcontrollers on boards using the LM6172
What boards using the LM6172 are built for
LM6172: common questions
Where can I find a LM6172 reference design?
Each of the 7 boards on this page is a real design using the LM6172. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM6172 pin 1?
Pin 1 has a series resistor on 6 of 6 designs, most often 1 kΩ (then 20 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM6172.
What resistor goes on the LM6172 - pin?
The - pins have a series resistor on 6 of 6 designs, most often 1 kΩ (then 20 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM6172.
What resistor goes on the LM6172 + pin?
The + pins have a series resistor on 6 of 6 designs, most often 8.2 kΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the LM6172.
What parts are used alongside the LM6172?
The 74HCT00, 74HCT04, 74HCT138, 74HCT244 and 74HCT74 appear in the most repositories here.
Which microcontrollers do boards using the LM6172 use?
Most are built on AVR/Arduino (2).
How big is a typical board using the LM6172?
The median is 184 × 80 mm, and 100% are two-layer designs.
What is the most popular open source board using the LM6172?
By GitHub stars, Adcboard by nuclearfutureslab, with 5 stars.
Can I simulate one of these boards using the LM6172 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.