17 open source boards using the LT3042xMSE

Real designs built with the LT3042xMSE, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

17 boardsClear filters|Most starred

How designs wire the LT3042xMSE

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LT3042xMSE connects to, and the resistors, capacitors and other passives placed on it.

  • The IN pins have a capacitor to GND on 6 of 7 designs, most often 4.7 µF (then 10 µF).
  • The EN/UV pin has a capacitor to GND on 6 of 7 designs, most often 4.7 µF (then 10 µF).
  • The SET pin has a capacitor to GND on 5 of 7 designs, most often 4.7 µF (then 100 nF).
  • The PG pin is left unconnected on 5 of 7 designs (a signal on 2).
INpin 1, 2Connected to: A connector 29% · 10V 29%
  • Capacitor to GND on 86% · 4.7 µF (6), 10 µF (4), 22 µF (4)
EN/UVpin 3Connected to: A connector 29% · 10V 29%
  • Capacitor to GND on 86% · 4.7 µF (3), 10 µF (2), 22 µF (2)
PGpin 4Connected to: Not connected 71% · a signal 29%
PGFBpin 6Connected to: A connector 29%
  • Capacitor to GND on 57% · 4.7 µF (2), 22 µF (2), 10 µF (1)
SETpin 7Connected to: Signal 100%
  • Capacitor to GND on 71% · 4.7 µF (4), 100 nF (1)
  • Resistor to GND on 57% · 49.9 kΩ (2), 90.9 kΩ (1), 33.2 kΩ (1)
  • Series resistor on 43% · 54.9 kΩ (1), 31 kΩ (1), 1.5 kΩ (1)
GNDpin 8, 11Connected to: GND 86%
OUTpin 10Connected to: 5.4V 71% · a signal 29%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 1fNoiseAmplifierRev13 by curtisseizert, 1" Photodetector - SOT23 by aewallin, R2RDAC2026 REVIZE II by ERDALECE and Pdmbrd by jaycordaro.

The LT3042xMSE in open source designs

The gallery holds 17 open source boards using the LT3042xMSE from 8 GitHub repositories; a typical one measures about 87.6 × 60.3 mm and carries around 56 components.

65% use four copper layers or more, and 35% carry an open source license.

The most starred is 1fNoiseAmplifierRev13 by curtisseizert.

Parts used alongside the LT3042xMSE

Microcontrollers on boards using the LT3042xMSE

LT3042xMSE: common questions

Where can I find a LT3042xMSE reference design?

Each of the 17 boards on this page is a real design using the LT3042xMSE. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LT3042xMSE IN pin connected?

The IN pins have a capacitor to GND on 6 of 7 designs, most often 4.7 µF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the LT3042xMSE.

How is the LT3042xMSE EN/UV pin connected?

The EN/UV pin has a capacitor to GND on 6 of 7 designs, most often 4.7 µF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the LT3042xMSE.

How is the LT3042xMSE SET pin connected?

The SET pin has a capacitor to GND on 5 of 7 designs, most often 4.7 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the LT3042xMSE.

Which microcontrollers do boards using the LT3042xMSE use?

Most are built on ESP32 (5) and STM32 (1).

How big is a typical board using the LT3042xMSE?

The median is 87.6 × 60.3 mm, and 35% are two-layer designs.

What is the most popular open source board using the LT3042xMSE?

By GitHub stars, 1fNoiseAmplifierRev13 by curtisseizert, with 35 stars.

Can I simulate one of these boards using the LT3042xMSE before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part