8 open source boards using the LY68L6400
Real designs built with the LY68L6400, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ICE-V-Wireless
ICE-V-Wireless
81.7 × 31.8 mm78 parts4LMIT82FPGA
Pogobot Head
nekonaute
43.2 × 43.2 mm129 parts4LMIT21ESP32
ESP32C3 FPGA
emeb
76.2 × 31.8 mm85 parts4LMIT16RP2040/RP2350
Hackquad
divisionind
26 × 48 mm91 parts4LGPL-3.00FPGA
Pcb dev fpga iCE40
shishir-dey
75.3 × 43.3 mm50 parts2LMIT0Pmod qspi psram
Wren6991
19 × 16.8 mm7 parts2LBSD-3-Clause1.5kPmod qspi psram
RafaGS
19 × 16.8 mm7 parts2LMIT19Pmod qspi psram
Adrian13985
19 × 16.8 mm7 parts2LNo license0
How designs wire the LY68L6400
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LY68L6400 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 1 µF).
- The CS pin has a pull-up to 3.3V on 4 of 8 designs, most often 10 kΩ.
- The CLK pin has a pull-up to 3.3V on 4 of 8 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: The microcontroller 50%, a connector 38% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| CLKpin 6 | Connected to: The microcontroller 63%, a connector 38% |
|
| VCCpin 8 | Connected to: 3.3V 88% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pmod qspi psram by Wren6991, ICE-V-Wireless by ICE-V-Wireless, Pogobot Head by nekonaute and Pmod qspi psram by RafaGS.
The LY68L6400 in open source designs
The gallery holds 8 open source boards using the LY68L6400 from 8 GitHub repositories; a typical one measures about 34.6 × 31.8 mm and carries around 64 components.
50% are two-layer designs, the rest use four layers or more, and 88% carry an open source license.
The most starred is Pmod qspi psram by Wren6991.
Parts used alongside the LY68L6400
Microcontrollers on boards using the LY68L6400
What boards using the LY68L6400 are built for
LY68L6400: common questions
Where can I find a LY68L6400 reference design?
Each of the 8 boards on this page is a real design using the LY68L6400. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LY68L6400 VCC pin?
The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 8 open source designs using the LY68L6400.
What pull-up resistor is used on the LY68L6400 CS pin?
The CS pin has a pull-up to 3.3V on 4 of 8 designs, most often 10 kΩ. Counted from the KiCad layouts of 8 open source designs using the LY68L6400.
What pull-up resistor is used on the LY68L6400 CLK pin?
The CLK pin has a pull-up to 3.3V on 4 of 8 designs, most often 10 kΩ. Counted from the KiCad layouts of 8 open source designs using the LY68L6400.
What parts are used alongside the LY68L6400?
The MCP73831-2-OT, 12MHz, DRTR5V0U4S, ice5lp4k_sg48 and MCP1824x-OT appear in the most repositories here.
Which microcontrollers do boards using the LY68L6400 use?
Most are built on ESP32 (2), FPGA (2) and RP2040/RP2350 (1).
How big is a typical board using the LY68L6400?
The median is 34.6 × 31.8 mm, and 50% are two-layer designs.
What is the most popular open source board using the LY68L6400?
By GitHub stars, Pmod qspi psram by Wren6991, with 1,509 stars.
Can I simulate one of these boards using the LY68L6400 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.