9 open source boards using the MAX11613
Real designs built with the MAX11613, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
DingoPDM
corygrant
72.4 × 95.3 mm151 parts4LMIT128STM32
Libre-MIG
JustEnoughDucks
161.1 × 95 mm154 parts2LCERN-OHL-S-2.022Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675STM32
Libre-MIG-rounded
JustEnoughDucks
161.1 × 95 mm154 parts2LCERN-OHL-S-2.022Radioberry preamp
saktheeswaranswan
65 × 56 mm137 parts2LNo license0Vswr extension bridge route
OE9SAU
83.7 × 37 mm50 parts2LNo license4Libre-MiG IO Controller
JustEnoughDucks
60 × 34.3 mm31 parts2LCERN-OHL-S-2.022Vswr extension bridge
OE9SAU
84 × 37 mm49 parts2LNo license4Vswr
OE9SAU
37 × 74 mm34 parts2LNo license4
How designs wire the MAX11613
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MAX11613 connects to, and the resistors, capacitors and other passives placed on it.
- The VOUT pins have a capacitor to GND on 4 of 5 designs, most often 4.7 nF (then 10 µF).
- The VDD pin has a capacitor to GND on 4 of 4 designs, most often 100 nF.
- The GND pins have a resistor to GND on 3 of 5 designs, most often 1 kΩ (then 1.8 kΩ).
- The GND pins have a capacitor to GND on 3 of 5 designs, most often 4.7 nF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 7 | Connected to: GND 56% · a signal 44% |
|
| VOUTpin 2, 4 | Connected to: A connector 40%, MCP6004 20% · 3.3V 30% |
|
| VINpin 3 | Connected to: Signal 60% · GND 20% · 5V 20% |
|
| VDDpin 8 | Connected to: 3.3V 50% · a signal 50% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Radioberry preamp by pa3gsb, DingoPDM by corygrant, Libre-MIG by JustEnoughDucks and Vswr by OE9SAU.
The MAX11613 in open source designs
The gallery holds 9 open source boards using the MAX11613 from 5 GitHub repositories; a typical one measures about 72.4 × 56 mm and carries around 137 components.
89% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Radioberry preamp by pa3gsb.
Parts used alongside the MAX11613
Microcontrollers on boards using the MAX11613
What boards using the MAX11613 are built for
MAX11613: common questions
Where can I find a MAX11613 reference design?
Each of the 9 boards on this page is a real design using the MAX11613. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MAX11613 VOUT pin connected?
The VOUT pins have a capacitor to GND on 4 of 5 designs, most often 4.7 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the MAX11613.
How is the MAX11613 VDD pin connected?
The VDD pin has a capacitor to GND on 4 of 4 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the MAX11613.
What resistor goes on the MAX11613 GND pin?
The GND pins have a resistor to GND on 3 of 5 designs, most often 1 kΩ (then 1.8 kΩ). Counted from the KiCad layouts of 5 open source designs using the MAX11613.
What parts are used alongside the MAX11613?
The INA199A1DC, LD1117S33, LP2985, MCP4662 and ST1S10 appear in the most repositories here.
Which microcontrollers do boards using the MAX11613 use?
Most are built on STM32 (3).
How big is a typical board using the MAX11613?
The median is 72.4 × 56 mm, and 89% are two-layer designs.
What is the most popular open source board using the MAX11613?
By GitHub stars, Radioberry preamp by pa3gsb, with 675 stars.
Can I simulate one of these boards using the MAX11613 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.