9 open source boards using the MC68B50
Real designs built with the MC68B50, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Minimal-6502
techav-homebrew
101.6 × 76.2 mm30 parts2LNo license5OSM39
christophetoularastel-eng
388.1 × 200 mm186 parts2LGPL-3.01SST-6809-V2.2
KenWillmott
100 × 100 mm46 parts4LMIT1AVR/Arduino
Retro-002
githubgilhad
100 × 100 mm295 parts4LGPL-3.00Hobgoblin
iley
150 × 110 mm52 parts2LNo license0Ssc
iley
100 × 80 mm31 parts2LNo license0AVR/Arduino
Retro-003
githubgilhad
100 × 100 mm247 parts4LGPL-3.00AVR/Arduino
Retro-001
githubgilhad
100 × 100 mm241 parts2LGPL-3.00AZ80 SIO
attraktorhh
110.3 × 40 mm10 parts2LMIT4
How designs wire the MC68B50
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the MC68B50 connects to, and the resistors, capacitors and other passives placed on it.
- The DCD pin is tied to GND on 7 of 7 designs.
- The IRQ pin has a pull-up to VCC on 5 of 7 designs, most often 4.7 kΩ (then 3.3 kΩ).
- The CTS pin is tied to GND on 6 of 7 designs.
- The RX_CLK pin has a crystal on 3 of 7 designs, most often 1.8432 MHz (then 7.3728 MHz).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 1 | Connected to: GND 100% | — |
| RX_CLKpin 3 | Connected to: Signal 100% |
|
| TX_CLKpin 4 | Connected to: Signal 100% |
|
| IRQpin 7 | Connected to: A connector 71%, HD6309 29%, Z80CPU 29% |
|
| VCCpin 12 | Connected to: VCC 100% |
|
| DCDpin 23 | Connected to: GND 100% | — |
| CTSpin 24 | Connected to: GND 86% | — |
17 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Minimal-6502 by techav-homebrew, AZ80 SIO by attraktorhh, OSM39 by christophetoularastel-eng and SST-6809-V2.2 by KenWillmott.
The MC68B50 in open source designs
The gallery holds 9 open source boards using the MC68B50 from 7 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 52 components.
67% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is Minimal-6502 by techav-homebrew.
Parts used alongside the MC68B50
Microcontrollers on boards using the MC68B50
What boards using the MC68B50 are built for
MC68B50: common questions
Where can I find a MC68B50 reference design?
Each of the 9 boards on this page is a real design using the MC68B50. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MC68B50 DCD pin connected?
The DCD pin is tied to GND on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MC68B50.
What pull-up resistor is used on the MC68B50 IRQ pin?
The IRQ pin has a pull-up to VCC on 5 of 7 designs, most often 4.7 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 7 open source designs using the MC68B50.
How is the MC68B50 CTS pin connected?
The CTS pin is tied to GND on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the MC68B50.
What parts are used alongside the MC68B50?
The 628128, 74HC14, 74HC74, 74LS04 and 74LS32 appear in the most repositories here.
Which microcontrollers do boards using the MC68B50 use?
Most are built on AVR/Arduino (3).
How big is a typical board using the MC68B50?
The median is 100 × 100 mm, and 67% are two-layer designs.
What is the most popular open source board using the MC68B50?
By GitHub stars, Minimal-6502 by techav-homebrew, with 5 stars.
Can I simulate one of these boards using the MC68B50 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.