10 open source boards using the MCP2551-I-P
Real designs built with the MCP2551-I-P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PIC
USBtin
Villanut0
32 × 65 mm21 parts2LNo license3Bluepill expansion
GinoAvanzini
90.9 × 73.2 mm43 parts2LGPL-3.02PIC
CAN-Bus-Car-Lights
sergimarsol
126.1 × 134.1 mm80 parts2LMIT0Nucleo-F767-Base-Board
Entruer
120 × 130 mm76 parts2LNo license0Bluepill expansion
rascimatec
90.9 × 73.2 mm43 parts2LNo license0NXP
Steering Wheel Main Board
tuftselectricracing
85 × 58 mm38 parts2LNo license0Kiwikit rpi pico draft
kiwih
70 × 59 mm25 parts2LMIT46ESP32
Main Board
jayalcock
55.4 × 54.6 mm64 parts2LNo license0NXP
DAQ Main Board
tuftselectricracing
116.2 × 57 mm26 parts2LNo license0NXP
DTS Board
EBOThor
167.6 × 81.3 mm80 parts2LMIT0
How designs wire the MCP2551-I-P
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the MCP2551-I-P connects to, and the resistors, capacitors and other passives placed on it.
- The CANL pin has a series resistor on 8 of 9 designs, most often 120 Ω (then 60 Ω).
- The VREF pin is left unconnected on 9 of 9 designs.
- The RS pin has a resistor to GND on 7 of 9 designs, most often 10 kΩ (then 1 kΩ).
- The CANH pin has a series resistor on 5 of 9 designs, most often 120 Ω (then 60 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 100% | — |
| VDDpin 3 | Connected to: 5V 100% |
|
| VREFpin 5 | Connected to: Not connected 100% | — |
| CANLpin 6 | Connected to: A connector 100% |
|
| CANHpin 7 | Connected to: A connector 100% |
|
| RSpin 8 | Connected to: Signal 78% · GND 22% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Kiwikit rpi pico draft by kiwih, USBtin by Villanut0, Bluepill expansion by GinoAvanzini and DTS Board by EBOThor.
The MCP2551-I-P in open source designs
The gallery holds 10 open source boards using the MCP2551-I-P from 9 GitHub repositories; a typical one measures about 90.9 × 69.1 mm and carries around 43 components.
100% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is Kiwikit rpi pico draft by kiwih.
Parts used alongside the MCP2551-I-P
What boards using the MCP2551-I-P are built for
MCP2551-I-P: common questions
Where can I find a MCP2551-I-P reference design?
Each of the 10 boards on this page is a real design using the MCP2551-I-P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP2551-I-P CANL pin?
The CANL pin has a series resistor on 8 of 9 designs, most often 120 Ω (then 60 Ω). Counted from the KiCad layouts of 9 open source designs using the MCP2551-I-P.
How is the MCP2551-I-P VREF pin connected?
The VREF pin is left unconnected on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the MCP2551-I-P.
What resistor goes on the MCP2551-I-P RS pin?
The RS pin has a resistor to GND on 7 of 9 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 9 open source designs using the MCP2551-I-P.
What parts are used alongside the MCP2551-I-P?
The BluePill_STM32F103C, L298HN and LM7805_TO220 appear in the most repositories here.
Which microcontrollers do boards using the MCP2551-I-P use?
Most are built on NXP (3), PIC (2) and ESP32 (1).
How big is a typical board using the MCP2551-I-P?
The median is 90.9 × 69.1 mm, and 100% are two-layer designs.
What is the most popular open source board using the MCP2551-I-P?
By GitHub stars, Kiwikit rpi pico draft by kiwih, with 46 stars.
Can I simulate one of these boards using the MCP2551-I-P before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.