9 open source boards using the MCP2562-H-SN
Real designs built with the MCP2562-H-SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
E9X-CAN-BT
Christian-Ristevski
74.8 × 49.8 mm88 parts2LNo license2Renesas
DRC-SLVD2025
hosh0344
60 × 45 mm58 parts2LNo license2STM32
Viaems
via
136 × 64 mm208 parts2LNo license0STM32
PUTM DV EBS 2022
PUT-Motorsport
97.9 × 67.4 mm121 parts2LNo license0STM32
Software dev board
awsmit07
83 × 53 mm81 parts4LNo license0STM32
PUTM EV APPS 2021
PUT-Motorsport
100.7 × 63.5 mm72 parts2LApache-2.00STM32
PUTM EV SteeringWheel 2021
PUT-Motorsport
92 × 92 mm69 parts2LApache-2.00PUTM EV PCB ON RASPBERRY 2022
PUT-Motorsport
57.5 × 40.6 mm39 parts2LNo license0Renesas
DRC-SVMD2025 Ver2.1
hosh0344
60 × 45 mm54 parts2LNo license2
How designs wire the MCP2562-H-SN
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the MCP2562-H-SN connects to, and the resistors, capacitors and other passives placed on it.
- The CANL pin has a series resistor on 7 of 8 designs, most often 120 Ω (then 100 kΩ).
- The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF.
- The CANH pin has a series resistor on 6 of 8 designs, most often 120 Ω (then 100 kΩ).
- The STBY pin is tied to GND on 6 of 8 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 75% · a signal 25% | — |
| VDDpin 3 | Connected to: 5V 100% |
|
| VIOpin 5 | Connected to: 3.3V 63% · a signal 38% |
|
| CANLpin 6 | Connected to: A connector 100% |
|
| CANHpin 7 | Connected to: A connector 100% |
|
| STBYpin 8 | Connected to: GND 75% · a signal 25% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include E9X-CAN-BT by Christian-Ristevski, DRC-SLVD2025 by hosh0344, Software dev board by awsmit07 and PUTM DV EBS 2022 by PUT-Motorsport.
The MCP2562-H-SN in open source designs
The gallery holds 9 open source boards using the MCP2562-H-SN from 8 GitHub repositories; a typical one measures about 83 × 53 mm and carries around 72 components.
89% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is E9X-CAN-BT by Christian-Ristevski.
Parts used alongside the MCP2562-H-SN
What boards using the MCP2562-H-SN are built for
MCP2562-H-SN: common questions
Where can I find a MCP2562-H-SN reference design?
Each of the 9 boards on this page is a real design using the MCP2562-H-SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP2562-H-SN CANL pin?
The CANL pin has a series resistor on 7 of 8 designs, most often 120 Ω (then 100 kΩ). Counted from the KiCad layouts of 8 open source designs using the MCP2562-H-SN.
What decoupling capacitors do designs use on the MCP2562-H-SN VDD pin?
The VDD pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF. Counted from the KiCad layouts of 8 open source designs using the MCP2562-H-SN.
What resistor goes on the MCP2562-H-SN CANH pin?
The CANH pin has a series resistor on 6 of 8 designs, most often 120 Ω (then 100 kΩ). Counted from the KiCad layouts of 8 open source designs using the MCP2562-H-SN.
What parts are used alongside the MCP2562-H-SN?
The LM1117-3.3, LM2596S-5, MCP2515-xSO and STM32L4P5RET6 appear in the most repositories here.
Which microcontrollers do boards using the MCP2562-H-SN use?
Most are built on STM32 (5), Renesas (2) and ESP32 (1).
How big is a typical board using the MCP2562-H-SN?
The median is 83 × 53 mm, and 89% are two-layer designs.
What is the most popular open source board using the MCP2562-H-SN?
By GitHub stars, E9X-CAN-BT by Christian-Ristevski, with 2 stars.
Can I simulate one of these boards using the MCP2562-H-SN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.