18 open source boards using the MCP4725
Real designs built with the MCP4725, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Sensor
chukhanhhoang
64.8 × 62 mm61 parts2LNo license14AVR/Arduino
Nano Lambda
ruzki
22.2 × 47 mm70 parts2LNo license9STM32
Generator 5351 rect sine
MR-DOS
102.4 × 102.4 mm280 parts2LGPL-3.06AVR/Arduino
Nano Lambda
chaosteam
22.2 × 47 mm70 parts2LNo license6FrequencyCounter
LUMERIIX
130 × 90 mm125 parts4LNo license5TI MSP430/CC
Huracan MkIII PreAmp Board
terjeio
175 × 86 mm175 parts2LNo license2Raspberry Pi
Sensor
ReshapeTUe
64.8 × 62 mm61 parts2LNo license2AVR/Arduino
PTDriver
wallaceowen
100 × 50 mm61 parts2LMIT1STM32
Sinthinator
phenax
100.9 × 144.5 mm53 parts2LNo license1- schematic only · 97 partsSTM32
Autonomous Ackermann
sachu018
97 partsNo license0 PCB Laser Exposer - Diode Driver
terjeio
28 × 35 mm22 parts2LCERN-OHL-1.217Microchip SAM
Pi TX 35W PA V2
M0LTE
100 × 100 mm161 parts4LNo license15Raspberry Pi
Raspberry Pi Zero W
chukhanhhoang
65 × 30 mm52 parts2LNo license14Raspberry Pi
Raspberry Pi Zero W
ReshapeTUe
65 × 30 mm52 parts2LNo license2Raspberry Pi
Raspberry Pi Zero W (original)
chukhanhhoang
65 × 30 mm52 parts2LNo license14Raspberry Pi
Raspberry Pi Zero W (original)
ReshapeTUe
65 × 30 mm52 parts2LNo license2MCP4725 breakout board for Arduino
6r1d
16.8 × 14.8 mm7 parts2LMIT2ESP32
IDM-FakeSensor-ESP
Xerolux
64 × 42 mm7 parts2LCERN-OHL-S-2.00
How designs wire the MCP4725
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the MCP4725 connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 10 of 13 designs, most often 4.7 kΩ (then 3 kΩ).
- The SCL pin has a pull-up to 3.3V on 10 of 13 designs, most often 4.7 kΩ (then 3 kΩ).
- The VDD pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTpin 1 | Connected to: LM358 23%, a connector 23% |
|
| VSSpin 2 | Connected to: GND 85% | — |
| VDDpin 3 | Connected to: 3.3V 77% · a signal 15% |
|
| SDApin 4 | Connected to: A connector 46%, the microcontroller 46%, MCP4725 46% |
|
| SCLpin 5 | Connected to: A connector 46%, MCP4725 46%, the microcontroller 38% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PCB Laser Exposer - Diode Driver by terjeio, Pi TX 35W PA V2 by M0LTE, Raspberry Pi Zero W by chukhanhhoang and Nano Lambda by ruzki.
The MCP4725 in open source designs
The gallery holds 18 open source boards using the MCP4725 from 14 GitHub repositories; a typical one measures about 65 × 47 mm and carries around 61 components.
88% are two-layer designs, the rest use four layers or more, and 28% carry an open source license.
The most starred is PCB Laser Exposer - Diode Driver by terjeio.
Parts used alongside the MCP4725
Microcontrollers on boards using the MCP4725
What boards using the MCP4725 are built for
MCP4725: common questions
Where can I find a MCP4725 reference design?
Each of the 18 boards on this page is a real design using the MCP4725. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP4725 SDA pin?
The SDA pin has a pull-up to 3.3V on 10 of 13 designs, most often 4.7 kΩ (then 3 kΩ). Counted from the KiCad layouts of 13 open source designs using the MCP4725.
What pull-up resistor is used on the MCP4725 SCL pin?
The SCL pin has a pull-up to 3.3V on 10 of 13 designs, most often 4.7 kΩ (then 3 kΩ). Counted from the KiCad layouts of 13 open source designs using the MCP4725.
What decoupling capacitors do designs use on the MCP4725 VDD pin?
The VDD pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 13 open source designs using the MCP4725.
What parts are used alongside the MCP4725?
The LM358, ADS1014IDGS, AMS1117-3.3, CJ125_32 and IRLZ44 appear in the most repositories here.
Which microcontrollers do boards using the MCP4725 use?
Most are built on Raspberry Pi (6), AVR/Arduino (3), STM32 (3) and ESP32 (1).
How big is a typical board using the MCP4725?
The median is 65 × 47 mm, and 88% are two-layer designs.
What is the most popular open source board using the MCP4725?
By GitHub stars, PCB Laser Exposer - Diode Driver by terjeio, with 17 stars.
Can I simulate one of these boards using the MCP4725 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.