14 open source boards using the MCP4922
Real designs built with the MCP4922, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Midi2cv
tomarus
81.3 × 96.5 mm63 parts2LNo license30EssentialShield
FandSonthesizer
84.5 × 100.4 mm61 parts2LGPL-3.04AVR/Arduino
DAC-for minimoog
gkaxowns9
132 × 100 mm49 parts2LNo license1STM32
Stm32-fpga oscilloscope
HexFud
160 × 100 mm115 parts4LNo license0Bachelor thesis
dario0603
99 × 99 mm57 parts2LNo license0LabPS
johannes51
95.3 × 92.7 mm43 parts2LNo license0LaserGameSystem
VectorSpaceHQ
82 × 91.2 mm42 parts2LGPL-3.00AVR/Arduino
Quantizer
QuinnFreedman
50 × 100 mm105 parts2LNo license114RP2040/RP2350
Pi pico itm39xxc if
mtguerreiro
116.8 × 77 mm104 parts2LBSD-3-Clause0AVR/Arduino
Envelope
QuinnFreedman
38 × 100 mm60 parts2LNo license114RP2040/RP2350
ModuleMid
ikechangexentrick
48.3 × 99.1 mm20 parts2LMIT0AVR/Arduino
Biodata
QuinnFreedman
28 × 100 mm53 parts2LNo license114AVR/Arduino
Drift
QuinnFreedman
18 × 100 mm34 parts2LNo license114AVR/Arduino
RNG Back
QuinnFreedman
50 × 100 mm34 parts2LNo license114
How designs wire the MCP4922
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the MCP4922 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 4 of 9 designs, most often 100 nF (then 10 µF).
- The VA pin has a series resistor on 4 of 9 designs, most often 10 kΩ (then 5 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 5V 100% |
|
| NCpin 2, 6, 7 | Connected to: Not connected 100% | — |
| VREFBpin 11 | Connected to: 5V 78% · a signal 22% | — |
| VSSpin 12 | Connected to: GND 89% | — |
| VREFApin 13 | Connected to: 5V 78% · a signal 22% |
|
| VApin 14 | Connected to: A connector 33% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Biodata by QuinnFreedman, Midi2cv by tomarus, EssentialShield PCB by FandSonthesizer and DAC-for minimoog by gkaxowns9.
The MCP4922 in open source designs
The gallery holds 14 open source boards using the MCP4922 from 10 GitHub repositories; a typical one measures about 81.7 × 100 mm and carries around 55 components.
93% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Quantizer by QuinnFreedman.
Microcontrollers on boards using the MCP4922
What boards using the MCP4922 are built for
MCP4922: common questions
Where can I find a MCP4922 reference design?
Each of the 14 boards on this page is a real design using the MCP4922. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP4922 VDD pin?
The VDD pin has a decoupling capacitor on 4 of 9 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 9 open source designs using the MCP4922.
What resistor goes on the MCP4922 VA pin?
The VA pin has a series resistor on 4 of 9 designs, most often 10 kΩ (then 5 kΩ). Counted from the KiCad layouts of 9 open source designs using the MCP4922.
What parts are used alongside the MCP4922?
The Arduino_Nano_v3.x, TL082, 6N138, 74HC595 and L7805 appear in the most repositories here.
Which microcontrollers do boards using the MCP4922 use?
Most are built on AVR/Arduino (7), RP2040/RP2350 (2) and STM32 (1).
How big is a typical board using the MCP4922?
The median is 81.7 × 100 mm, and 93% are two-layer designs.
What is the most popular open source board using the MCP4922?
By GitHub stars, Quantizer by QuinnFreedman, with 114 stars.
Can I simulate one of these boards using the MCP4922 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.