65 open source boards using the 6N138
Real designs built with the 6N138, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Drumkid
mattybrad
90 × 140 mm57 parts2LMIT137RP2040/RP2350
AS3397 proto DIP
PhysicsDptAngers
167.6 × 97.5 mm138 parts2LMIT87RP2040/RP2350
Kerberos
FrankBuss
62.5 × 83.8 mm167 parts4LNo license82NXP
Teensy eurorack
newdigate
64.8 × 109.2 mm52 parts2LMIT27NXP
Fjol
hallmar
184.7 × 110.7 mm204 parts2LNo license21RP2040/RP2350
Pico midi2cv
peterzimon
75 × 100 mm37 parts2LNo license13MIDI4MiSTer
KabukiFlux
44 × 44.8 mm27 parts2LMIT13AVR/Arduino
Beat707
FrankBuss
276.9 × 142.2 mm263 parts2LNo license1110knobs PT8211
tomcombriat
99.9 × 80 mm56 parts2LGPL-3.09AVR/Arduino
Mainboard
jypma
39.4 × 108 mm122 parts2LNo license8SoundX
SukkoPera
60.8 × 100 mm44 parts2LNo license8AVR/Arduino
Alpha.ctrl
banjomasterpete
265 × 200 mm113 parts2LMIT6Midi uart adapter
tschiemer
39.4 × 48.3 mm11 parts2LMIT5EssentialShield
FandSonthesizer
84.5 × 100.4 mm61 parts2LGPL-3.04WEASEL
joebmz98
335 × 200 mm216 parts2LMIT3RP2040/RP2350
V4d2 pico
tomcombriat
54.2 × 94.2 mm99 parts2LTAPR-OHL-1.03AVR/Arduino
SCOUT2
oskitone
221.4 × 52.3 mm88 parts2LNo license3AVR/Arduino
Arduino-MIDI-Floppy-Drive-Instrument
jzkmath
101.6 × 53.3 mm33 parts2LGPL-3.03AVR/Arduino
C64UserPortMidi
relic-se
62.5 × 47.5 mm25 parts2LGPL-3.03STM32
Stm32-midi to cv
peterzimon
39.9 × 99.9 mm45 parts2LNo license2Noise toaster
adeboni
128 × 129 mm133 parts2LGPL-3.01ESP32
T8-Sequencer
lluisestape-upc
290 × 210 mm96 parts2LMIT1ESP32
Esp32-midi processor
andymann
108 × 97.4 mm50 parts2LNo license1AVR/Arduino
DAC-for minimoog
gkaxowns9
132 × 100 mm49 parts2LNo license1RP2040/RP2350
PicoTracker th
alexbonhomme
91.4 × 110 mm29 parts2LNo license1STM32
SplitBoard8Voice
hsetlik
310 × 199 mm517 parts4LNo license0NXP
TeensyPolySynth
ajharvie
355.6 × 97.8 mm81 parts2LNo license0Drumkid
sinitsinmike
90 × 140 mm57 parts2LMIT0Microchip SAM
Samd21g midi tool
newdigate
81.4 × 60 mm54 parts4LMIT0AVR/Arduino
Distel hardware
schmolmo
175.5 × 94.5 mm25 parts2LNo license0Game midi breakout
epakai
24.2 × 12.2 mm18 parts2LGPL-3.00ESP32
AirMidi
TTeuber
72 × 46 mm18 parts2LMIT0ESP32
AirMidi firmware
cxandy
72 × 46 mm18 parts2LMIT0Breadboard midi
mprosk
45.7 × 31.8 mm14 parts2LNo license0Rhythmsquid
edwindertien
39.3 × 21.2 mm13 parts2LNo license0Teensy eurorack breakout
newdigate
110.5 × 111.1 mm73 parts2LMIT258
How designs wire the 6N138
Read from the KiCad layouts of 49 open source designs, one per repository: what each pin of the 6N138 connects to, and the resistors, capacitors and other passives placed on it.
- The C1 pin has a series resistor on 48 of 49 designs, most often 220 Ω (then 100 Ω).
- The VO2 pin has a pull-up to 3.3V on 40 of 48 designs, most often 220 Ω (then 470 Ω).
- The VO1 pin has a resistor to GND on 27 of 48 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 4 | Connected to: Not connected 98% | — |
| C1pin 2 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 92% | — |
| VO2pin 6 | Connected to: The microcontroller 38%, a connector 33% |
|
| VO1pin 7 | Connected to: Signal 60% · not connected 40% |
|
| VCCpin 8 | Connected to: 5V 90% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Teensy eurorack breakout by newdigate, Edrumulus by corrados, Drumkid by mattybrad and AS3397-Conductor by PhysicsDptAngers.
The 6N138 in open source designs
The gallery holds 65 open source boards using the 6N138 from 50 GitHub repositories; a typical one measures about 90 × 97.5 mm and carries around 56 components.
94% are two-layer designs, the rest use four layers or more, and 55% carry an open source license.
The most starred is Teensy eurorack breakout by newdigate.
Parts used alongside the 6N138
Microcontrollers on boards using the 6N138
What boards using the 6N138 are built for
6N138: common questions
Where can I find a 6N138 reference design?
Each of the 65 boards on this page is a real design using the 6N138. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 6N138 C1 pin?
The C1 pin has a series resistor on 48 of 49 designs, most often 220 Ω (then 100 Ω). Counted from the KiCad layouts of 49 open source designs using the 6N138.
What pull-up resistor is used on the 6N138 VO2 pin?
The VO2 pin has a pull-up to 3.3V on 40 of 48 designs, most often 220 Ω (then 470 Ω). Counted from the KiCad layouts of 49 open source designs using the 6N138.
What resistor goes on the 6N138 VO1 pin?
The VO1 pin has a resistor to GND on 27 of 48 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 49 open source designs using the 6N138.
What parts are used alongside the 6N138?
The L7805, TL074, 74HC14, 74LS14 and MCP4822 appear in the most repositories here.
Which microcontrollers do boards using the 6N138 use?
Most are built on AVR/Arduino (16), RP2040/RP2350 (8), ESP32 (6) and NXP (6).
How big is a typical board using the 6N138?
The median is 90 × 97.5 mm, and 94% are two-layer designs.
What is the most popular open source board using the 6N138?
By GitHub stars, Teensy eurorack breakout by newdigate, with 258 stars.
Can I simulate one of these boards using the 6N138 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.