20 open source boards using the MCP6001T-I/OT
Real designs built with the MCP6001T-I/OT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
MCU-Link-MR
ErichStyger
57.9 × 39.9 mm107 parts2LMIT20PCB B
dragondgold
54 × 54 mm68 parts2LGPL-3.05STM32
6U5 MCU Board
donpivo
20 × 52 mm27 parts2LNo license3PCB B
dragondgold
54 × 54 mm75 parts2LGPL-3.01STM32
Board
Filip-Kin
84 × 141 mm235 parts2LNo license0ESP32
Robot
jgraulle
100 × 100 mm183 parts2LNo license0DisCuInv
cezarbontas333
237.5 × 135.5 mm92 parts4LCERN-OHL-S-2.00AVR/Arduino
Wedding keepsake
ericmcdaniel
80 × 30 mm85 parts4LMIT0STM32
24v to-5v-50w buck converter stm32
HakanD1
91.4 × 75.6 mm83 parts2LMIT0ESP32
NIVA-pod
https-shubhamsahu
34 × 48 mm62 parts4LNo license0AVR/Arduino
Kicad sensor interface board
RangeMaster370
54 × 42 mm36 parts2LNo license0- schematic only · 39 partsSTM32
Super-8-Camera
breilly1296
39 partsNo license0 Bms csc
olin-electric-motorsports
183.7 × 31.1 mm112 parts2LMIT13STM32
Radio kiosk
Filip-Kin
84 × 133 mm188 parts2LNo license0ANC Helmet - satellite board (right earcup)
baba2712
34 × 26 mm42 parts2LMIT0STM32
Radio kiosk fixed
Filip-Kin
84 × 133 mm188 parts2LNo license0Data aquisition module
olin-electric-motorsports
86 × 34.4 mm67 parts4LMIT13AN R 2R
laforestlabs
55.4 × 31.8 mm22 parts2LNo license0STM32
Bms core
olin-electric-motorsports
109.8 × 25.1 mm61 parts4LMIT13Tsal ail
olin-electric-motorsports
94.4 × 42.5 mm60 parts2LMIT13
How designs wire the MCP6001T-I/OT
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the MCP6001T-I/OT connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 14 of 14 designs.
- The - pin has a series resistor on 9 of 14 designs, most often 100 Ω (then 10 kΩ).
- The V+ pin has a decoupling capacitor on 9 of 14 designs, most often 100 nF (then 1 µF).
- The VOUT pin has a series resistor on 8 of 14 designs, most often 100 Ω (then 10 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTpin 1 | Connected to: A connector 29% |
|
| V-pin 2 | Connected to: GND 100% | — |
| +pin 3 | Connected to: Signal 93% |
|
| -pin 4 | Connected to: A connector 29% |
|
| V+pin 5 | Connected to: 3.3V 86% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MCU-Link-MR by ErichStyger, Bms core by olin-electric-motorsports, PCB B by dragondgold and 6U5 MCU Board by donpivo.
The MCP6001T-I/OT in open source designs
The gallery holds 20 open source boards using the MCP6001T-I/OT from 15 GitHub repositories; a typical one measures about 84 × 48 mm and carries around 72 components.
74% are two-layer designs, the rest use four layers or more, and 55% carry an open source license.
The most starred is MCU-Link-MR by ErichStyger.
Parts used alongside the MCP6001T-I/OT
Microcontrollers on boards using the MCP6001T-I/OT
What boards using the MCP6001T-I/OT are built for
MCP6001T-I/OT: common questions
Where can I find a MCP6001T-I/OT reference design?
Each of the 20 boards on this page is a real design using the MCP6001T-I/OT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP6001T-I/OT V- pin connected?
The V- pin is tied to GND on 14 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the MCP6001T-I/OT.
What resistor goes on the MCP6001T-I/OT - pin?
The - pin has a series resistor on 9 of 14 designs, most often 100 Ω (then 10 kΩ). Counted from the KiCad layouts of 14 open source designs using the MCP6001T-I/OT.
What decoupling capacitors do designs use on the MCP6001T-I/OT V+ pin?
The V+ pin has a decoupling capacitor on 9 of 14 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 14 open source designs using the MCP6001T-I/OT.
What parts are used alongside the MCP6001T-I/OT?
The ADP2108AUJZ-3.3-R7, AMS1117-3.3, BQ27441DRZR-G1A, INA194AIDBVR and MCP1642B-50I/MS appear in the most repositories here.
Which microcontrollers do boards using the MCP6001T-I/OT use?
Most are built on STM32 (7), AVR/Arduino (2) and ESP32 (2).
How big is a typical board using the MCP6001T-I/OT?
The median is 84 × 48 mm, and 74% are two-layer designs.
What is the most popular open source board using the MCP6001T-I/OT?
By GitHub stars, MCU-Link-MR by ErichStyger, with 20 stars.
Can I simulate one of these boards using the MCP6001T-I/OT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.