11 open source boards using the MCP6001U
Real designs built with the MCP6001U, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Flight-Controller
MarkSherstan
50 × 50 mm74 parts2LMIT3STM32
Bread board
cr1tbit
100 × 77 mm224 parts4LNo license0STM32
SPECTRA-MX-1-
landjas09
60 × 75 mm110 parts4LNo license0Panel daisy
ohmtech-rdi
148 × 84.5 mm20 parts2LCC-BY-SA-4.0405ESP32
Hubby
cr1tbit
100 × 77 mm212 parts4LNo license0Panel daisy
GKeyMaster
148 × 84.5 mm20 parts2LCC-BY-SA-4.00Td rgbinput lm1205
tdaede
100 × 50 mm72 parts2LNo license370SMB - 100 - A
Rudolfs-Pakalns
92 × 49.5 mm39 parts2LNo license0Sensorilauta
chiplet
29.2 × 29.5 mm12 parts2LNo license0Cv in
ohmtech-rdi
25 × 19 mm13 parts2LCC-BY-SA-4.0405Cv in
GKeyMaster
25 × 19 mm13 parts2LCC-BY-SA-4.00
How designs wire the MCP6001U
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the MCP6001U connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 1 µF).
- The V- pin is tied to GND on 8 of 8 designs.
- Pin 4 has a series resistor on 6 of 8 designs, most often 10 kΩ (then 20 kΩ).
- The - pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 20 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| +pin 1 | Connected to: Signal 63% · GND 25% |
|
| V-pin 2 | Connected to: GND 100% | — |
| -pin 3 | Connected to: Signal 100% |
|
| Pin 4 | Connected to: A connector 50% |
|
| V+pin 5 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Cv in by ohmtech-rdi, Td rgbinput lm1205 by tdaede, Flight-Controller-PCB by MarkSherstan and Sensorilauta by chiplet.
The MCP6001U in open source designs
The gallery holds 11 open source boards using the MCP6001U from 8 GitHub repositories; a typical one measures about 92 × 50 mm and carries around 39 components.
73% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.
The most starred is Panel daisy by ohmtech-rdi.
Parts used alongside the MCP6001U
Microcontrollers on boards using the MCP6001U
What boards using the MCP6001U are built for
MCP6001U: common questions
Where can I find a MCP6001U reference design?
Each of the 11 boards on this page is a real design using the MCP6001U. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP6001U V+ pin?
The V+ pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 8 open source designs using the MCP6001U.
How is the MCP6001U V- pin connected?
The V- pin is tied to GND on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the MCP6001U.
What resistor goes on the MCP6001U pin 4?
Pin 4 has a series resistor on 6 of 8 designs, most often 10 kΩ (then 20 kΩ). Counted from the KiCad layouts of 8 open source designs using the MCP6001U.
Which microcontrollers do boards using the MCP6001U use?
Most are built on STM32 (2), AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the MCP6001U?
The median is 92 × 50 mm, and 73% are two-layer designs.
What is the most popular open source board using the MCP6001U?
By GitHub stars, Panel daisy by ohmtech-rdi, with 405 stars.
Can I simulate one of these boards using the MCP6001U before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.