13 open source boards using the AZ1117-ADJ

Real designs built with the AZ1117-ADJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the AZ1117-ADJ

Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the AZ1117-ADJ connects to, and the resistors, capacitors and other passives placed on it.

  • The VI pin has a decoupling capacitor on 9 of 10 designs, most often 10 µF (then 100 nF).
  • The ADJ pin has a resistor to GND on 8 of 10 designs, most often 680 Ω (then 2.2 kΩ).
  • The ADJ pin has a pull-up to 5V on 7 of 10 designs, most often 220 Ω (then 280 Ω).
  • The VO pin has a decoupling capacitor on 6 of 10 designs, most often 10 µF (then 22 µF).
ADJpin 1Connected to: Signal 80% · GND 20%
  • Resistor to GND on 80% · 680 Ω (3), 2.2 kΩ (1), 360 Ω (1)
  • Pull-up to 5V on 70% · 220 Ω (3), 280 Ω (1), 120 Ω (1)
VOpin 2Connected to: 5V 90%
  • Decoupling capacitor on 60% · 10 µF (3), 22 µF (2), 100 nF (1)
VIpin 3Connected to: 12V 50% · a signal 50%
  • Decoupling capacitor on 90% · 10 µF (10), 100 nF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Td rgbinput lm1205 by tdaede, STM32F7 FC by rishikesh2715, FreeDSP Catamaran by freeDSP and FreeDSP Classic SMD AB plus-II by CyberPit.

The AZ1117-ADJ in open source designs

The gallery holds 13 open source boards using the AZ1117-ADJ from 10 GitHub repositories; a typical one measures about 100 × 77 mm and carries around 190 components.

54% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.

The most starred is Td rgbinput lm1205 by tdaede.

Microcontrollers on boards using the AZ1117-ADJ

AZ1117-ADJ: common questions

Where can I find a AZ1117-ADJ reference design?

Each of the 13 boards on this page is a real design using the AZ1117-ADJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the AZ1117-ADJ VI pin?

The VI pin has a decoupling capacitor on 9 of 10 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 10 open source designs using the AZ1117-ADJ.

What resistor goes on the AZ1117-ADJ ADJ pin?

The ADJ pin has a resistor to GND on 8 of 10 designs, most often 680 Ω (then 2.2 kΩ). Counted from the KiCad layouts of 10 open source designs using the AZ1117-ADJ.

What decoupling capacitors do designs use on the AZ1117-ADJ VO pin?

The VO pin has a decoupling capacitor on 6 of 10 designs, most often 10 µF (then 22 µF). Counted from the KiCad layouts of 10 open source designs using the AZ1117-ADJ.

What parts are used alongside the AZ1117-ADJ?

The 24AA256, ADAU1701, LME49720, AT7456E and BMP388 appear in the most repositories here.

Which microcontrollers do boards using the AZ1117-ADJ use?

Most are built on STM32 (4) and ESP32 (1).

How big is a typical board using the AZ1117-ADJ?

The median is 100 × 77 mm, and 54% are two-layer designs.

What is the most popular open source board using the AZ1117-ADJ?

By GitHub stars, Td rgbinput lm1205 by tdaede, with 370 stars.

Can I simulate one of these boards using the AZ1117-ADJ before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part