15 open source boards using the MCP6002-I/SN
Real designs built with the MCP6002-I/SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Module17
M17-Project
100 × 83 mm186 parts4LCERN-OHL-W-2.0129RP2040/RP2350
MMM main
niektb
40 × 110 mm145 parts4LCC-BY-SA-4.034Microchip SAM
GateDr mainboard
PajamaLlamaLand
47 × 106 mm111 parts4LNo license1- schematic only · 1344 partsRP2040/RP2350
LZ-1-Backplane
HynixCJR
1344 parts2LNo license1 ESP32
Senzori iradiere
cs-pub-ro
103 × 126 mm328 parts4LNo license0Board
thomasparlette
140.9 × 163.4 mm237 parts8LNo license0FPGA
Courant
KrasForge
160 × 100 mm180 parts6LMIT0AVR/Arduino
Mie1001 daq board
Chaospossum
68.6 × 53.3 mm38 parts2LNo license0RP2040/RP2350
PocketChime-R2R 8-Bit Ladder Chiptune Synth
draarivpatel-ui
78 × 56 mm31 parts2LMIT0Analog front end lab
limatthew01-hue
60 × 40 mm14 parts2LNo license0FPGA
Courant.before colored actual models 20260918T190457
KrasForge
160 × 100 mm180 parts6LMIT0AVR/Arduino
Mie1001 daq simple
Chaospossum
68.6 × 53.3 mm31 parts2LNo license0RP2040/RP2350
Toepler plus
niektb
20 × 106 mm112 parts2LCC-BY-SA-4.034Andes
niektb
40 × 110 mm109 parts2LCC-BY-SA-4.034RP2040/RP2350
PI SCOPE
niektb
40 × 110 mm97 parts2LCC-BY-SA-4.034
How designs wire the MCP6002-I/SN
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the MCP6002-I/SN connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 7 of 9 designs, most often 100 kΩ (then 100 Ω).
- The V+ pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 1 µF).
- The V- pin is tied to GND on 8 of 9 designs.
- The P1 pin has a series resistor on 6 of 9 designs, most often 100 Ω (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| P1pin 1 | Connected to: A connector 22% |
|
| -pin 2, 6 | Connected to: Signal 72% |
|
| +pin 3, 5 | Connected to: Signal 67% · GND 22% |
|
| V-pin 4 | Connected to: GND 89% | — |
| P7pin 7 | Connected to: Signal 67% · not connected 22% |
|
| V+pin 8 | Connected to: 3.3V 67% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Module17 by M17-Project, Andes by niektb, GateDr mainboard by PajamaLlamaLand and Mie1001 daq board by Chaospossum.
The MCP6002-I/SN in open source designs
The gallery holds 15 open source boards using the MCP6002-I/SN from 10 GitHub repositories; a typical one measures about 68.6 × 103 mm and carries around 112 components.
53% are two-layer designs, the rest use four layers or more, and 53% carry an open source license.
The most starred is Module17 by M17-Project.
Parts used alongside the MCP6002-I/SN
Microcontrollers on boards using the MCP6002-I/SN
What boards using the MCP6002-I/SN are built for
MCP6002-I/SN: common questions
Where can I find a MCP6002-I/SN reference design?
Each of the 15 boards on this page is a real design using the MCP6002-I/SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP6002-I/SN - pin?
The - pins have a series resistor on 7 of 9 designs, most often 100 kΩ (then 100 Ω). Counted from the KiCad layouts of 9 open source designs using the MCP6002-I/SN.
What decoupling capacitors do designs use on the MCP6002-I/SN V+ pin?
The V+ pin has a decoupling capacitor on 7 of 9 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 9 open source designs using the MCP6002-I/SN.
How is the MCP6002-I/SN V- pin connected?
The V- pin is tied to GND on 8 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the MCP6002-I/SN.
Which microcontrollers do boards using the MCP6002-I/SN use?
Most are built on RP2040/RP2350 (5), AVR/Arduino (2), FPGA (2) and ESP32 (1).
How big is a typical board using the MCP6002-I/SN?
The median is 68.6 × 103 mm, and 53% are two-layer designs.
What is the most popular open source board using the MCP6002-I/SN?
By GitHub stars, Module17 by M17-Project, with 129 stars.
Can I simulate one of these boards using the MCP6002-I/SN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.