16 open source boards using the MIC4427

Real designs built with the MIC4427, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

16 boardsClear filters|Most starred

How designs wire the MIC4427

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the MIC4427 connects to, and the resistors, capacitors and other passives placed on it.

  • The V+ pin has a decoupling capacitor on 8 of 13 designs, most often 100 nF (then 4.7 µF).
NCpin 1, 8Connected to: Not connected 100%
IN_Apin 2Connected to: The microcontroller 77%
  • Resistor to GND on 38% · 10 kΩ (4), 1 kΩ (1)
GNDpin 3Connected to: GND 85% · a signal 15%
IN_Bpin 4Connected to: The microcontroller 77%
  • Resistor to GND on 38% · 10 kΩ (4), 1 kΩ (1)
OUT_Bpin 5Connected to: A connector 23%
  • Series resistor on 38% · 100 Ω (3), 10 Ω (1)
V+pin 6Connected to: 12V 54% · a signal 46%
  • Decoupling capacitor on 62% · 100 nF (8), 4.7 µF (1), 330 µF (1)
OUT_Apin 7Connected to: A connector 23%
  • Series resistor on 38% · 100 Ω (3), 10 Ω (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Td deflect by tdaede, Micro rusEFI by rusefi, MicroRusEFI by rusefi and STM32F103RB USB to UART SPI I2C by Stulinaz.

The MIC4427 in open source designs

The gallery holds 16 open source boards using the MIC4427 from 13 GitHub repositories; a typical one measures about 88.9 × 80.2 mm and carries around 150 components.

88% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.

The most starred is Td deflect by tdaede.

Microcontrollers on boards using the MIC4427

MIC4427: common questions

Where can I find a MIC4427 reference design?

Each of the 16 boards on this page is a real design using the MIC4427. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the MIC4427 V+ pin?

The V+ pin has a decoupling capacitor on 8 of 13 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 13 open source designs using the MIC4427.

What parts are used alongside the MIC4427?

The LM1117-3.3, TLE9201SG, VNLD5090, MCP6004 and molex_48pin_MRE appear in the most repositories here.

Which microcontrollers do boards using the MIC4427 use?

Most are built on STM32 (11), AVR/Arduino (2) and ESP32 (1).

How big is a typical board using the MIC4427?

The median is 88.9 × 80.2 mm, and 88% are two-layer designs.

What is the most popular open source board using the MIC4427?

By GitHub stars, Td deflect by tdaede, with 370 stars.

Can I simulate one of these boards using the MIC4427 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part