15 open source boards using the TLE9201SG

Real designs built with the TLE9201SG, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

15 boardsClear filters|Most starred

How designs wire the TLE9201SG

Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the TLE9201SG connects to, and the resistors, capacitors and other passives placed on it.

  • The DIS pin has a pull-up to 3.3V on 10 of 10 designs, most often 10 kΩ (then 4.7 kΩ).
  • The OUT1 pin has a capacitor to GND on 7 of 12 designs, most often 10 nF.
  • The OUT2 pin has a capacitor to GND on 7 of 12 designs, most often 10 nF.
  • The SO pin is left unconnected on 8 of 12 designs (a signal on 4).
VSOpin 2Connected to: 3.3V 83% · a signal 17%
SOpin 3Connected to: Not connected 67% · a signal 33%
VSpin 4Connected to: 12V 75% · GND 17%
  • Decoupling capacitor on 50% · 10 µF (17), 100 nF (4), 470 µF (1)
OUT1pin 5Connected to: A connector 42% · GND 17%
  • Capacitor to GND on 58% · 10 nF (7)
  • Series resistor on 33% · 4.7 kΩ (3)
GNDpin 6, 13Connected to: GND 100%
OUT2pin 7Connected to: A connector 42%
  • Capacitor to GND on 58% · 10 nF (7)
  • Series resistor on 33% · 4.7 kΩ (3)
CSNpin 9Connected to: GND 67% · not connected 25%
DISpin 11Connected to: The microcontroller 50%
  • Pull-up to 3.3V on 100% · 10 kΩ (6), 4.7 kΩ (4)
PWMpin 12Connected to: The microcontroller 50%, a connector 20%
  • Resistor to GND on 30% · 10 kΩ (3)

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Micro rusEFI by rusefi, Proteus by mck1117, MicroRusEFI by rusefi and Hellen1-motor driver by andreika-git.

The TLE9201SG in open source designs

The gallery holds 15 open source boards using the TLE9201SG from 12 GitHub repositories; a typical one measures about 96.5 × 100 mm and carries around 235 components.

60% use four copper layers or more, and 0% carry an open source license.

The most starred is Micro rusEFI by rusefi.

Microcontrollers on boards using the TLE9201SG

What boards using the TLE9201SG are built for

TLE9201SG: common questions

Where can I find a TLE9201SG reference design?

Each of the 15 boards on this page is a real design using the TLE9201SG. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the TLE9201SG DIS pin?

The DIS pin has a pull-up to 3.3V on 10 of 10 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 12 open source designs using the TLE9201SG.

How is the TLE9201SG OUT1 pin connected?

The OUT1 pin has a capacitor to GND on 7 of 12 designs, most often 10 nF. Counted from the KiCad layouts of 12 open source designs using the TLE9201SG.

How is the TLE9201SG OUT2 pin connected?

The OUT2 pin has a capacitor to GND on 7 of 12 designs, most often 10 nF. Counted from the KiCad layouts of 12 open source designs using the TLE9201SG.

What parts are used alongside the TLE9201SG?

The JDY-33, MCP6004, LM1117-3.3, MCP6004T-I/ST and MIC4427 appear in the most repositories here.

Which microcontrollers do boards using the TLE9201SG use?

Most are built on STM32 (8).

How big is a typical board using the TLE9201SG?

The median is 96.5 × 100 mm, and 40% are two-layer designs.

What is the most popular open source board using the TLE9201SG?

By GitHub stars, Micro rusEFI by rusefi, with 98 stars.

Can I simulate one of these boards using the TLE9201SG before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part