15 open source boards using the MLPF-WB55-01E3
Real designs built with the MLPF-WB55-01E3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
TekTag BioSensor
teklabsdigital
26 × 25 mm77 parts6LMIT19STM32
Bat trial tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
ACwing FC A
ACwing-UAV
40.8 × 40.8 mm98 parts4LNo license0STM32
ACwing FC A
andrea-cirillo
40.8 × 40.8 mm97 parts4LNo license0STM32
ACwing FC A
andrea-cirillo
40.8 × 40.8 mm97 parts4LNo license0STM32
Stm32 flight controller hw
andrea-cirillo
40 × 40 mm96 parts4LNo license0STM32
Gpio bank v2 tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Gpio probe tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Gpio v2 tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Heart v2
vexpaer
100 × 32 mm159 parts4LCERN-OHL-S-2.00STM32
Heart v2 placement only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Heart v2 tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Imu int trial tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Nrst tracks only
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00STM32
Placement candidate imu
vexpaer
100 × 30 mm159 parts4LCERN-OHL-S-2.00
How designs wire the MLPF-WB55-01E3
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MLPF-WB55-01E3 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT_A1 pin has a series resistor on 5 of 5 designs, most often 0 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT_A1pin A1 | Connected to: Signal 100% |
|
| GND_A2pin A2 | Connected to: GND 100% | — |
| GND_B1pin B1 | Connected to: GND 100% | — |
| GND_B2pin B2 | Connected to: GND 100% | — |
| GND_B3pin B3 | Connected to: GND 100% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TekTag BioSensor by teklabsdigital, ACwing FC A by ACwing-UAV, ACwing FC A by andrea-cirillo and ACwing FC A by andrea-cirillo.
The MLPF-WB55-01E3 in open source designs
The gallery holds 15 open source boards using the MLPF-WB55-01E3 from 6 GitHub repositories; a typical one measures about 100 × 30 mm and carries around 159 components.
100% use four copper layers or more, and 73% carry an open source license.
The most starred is TekTag BioSensor by teklabsdigital.
Parts used alongside the MLPF-WB55-01E3
Microcontrollers on boards using the MLPF-WB55-01E3
What boards using the MLPF-WB55-01E3 are built for
MLPF-WB55-01E3: common questions
Where can I find a MLPF-WB55-01E3 reference design?
Each of the 15 boards on this page is a real design using the MLPF-WB55-01E3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MLPF-WB55-01E3 OUT_A1 pin?
The OUT_A1 pin has a series resistor on 5 of 5 designs, most often 0 Ω. Counted from the KiCad layouts of 6 open source designs using the MLPF-WB55-01E3.
What parts are used alongside the MLPF-WB55-01E3?
The LD39130SPUR, LSM6DSV16XTR, STM32WB55CGU6, USBLC6-2SC6 and IIS2MDCTR appear in the most repositories here.
Which microcontrollers do boards using the MLPF-WB55-01E3 use?
Most are built on STM32 (15).
How big is a typical board using the MLPF-WB55-01E3?
The median is 100 × 30 mm, and 0% are two-layer designs.
What is the most popular open source board using the MLPF-WB55-01E3?
By GitHub stars, TekTag BioSensor by teklabsdigital, with 19 stars.
Can I simulate one of these boards using the MLPF-WB55-01E3 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.