9 open source boards using the PCA9548APW
Real designs built with the PCA9548APW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Chu Pico Main
whowechina
294 × 100 mm109 parts2LCC-BY-NC-4.01914ch-RF-FE
JohnnyGOX17
249.9 × 94.7 mm275 parts4LMIT5AVR/Arduino
MF RMP Panel
stefanofinetti
142 × 83 mm115 parts2LGPL-3.01ESP32
Chess board
shuki25
317.5 × 228.6 mm461 parts4LNo license0ESP32
Robotpcbv1
NIKOLAI-GOGOL444
52.1 × 52.1 mm85 parts4LApache-2.00ESP32
Smart chessboard controller
shuki25
89.8 × 92.5 mm54 parts4LNo license0AVR/Arduino
OVHD Mainboard
stefanofinetti
137 × 89 mm123 parts2LGPL-3.05AVR/Arduino
Chessconnect uP
K-0hm
100 × 100 mm88 parts2LGPL-3.00I2C splitter
arneman44
41.2 × 28.2 mm20 parts2LNo license0
How designs wire the PCA9548APW
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the PCA9548APW connects to, and the resistors, capacitors and other passives placed on it.
- The SD0 pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 1.2 kΩ).
- The SC0 pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 1.2 kΩ).
- The SCL pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 67% · a signal 33% | — |
| A1pin 2 | Connected to: GND 67% · a signal 33% | — |
| RESETpin 3 | Connected to: The microcontroller 22% |
|
| SD0pin 4 | Connected to: A connector 44% |
|
| SC0pin 5 | Connected to: A connector 44% |
|
| SD1pin 6 | Connected to: A connector 33% · not connected 22% |
|
| SC1pin 7 | Connected to: A connector 33% · not connected 22% |
|
| SD2pin 8 | Connected to: A connector 33% |
|
| SC2pin 9 | Connected to: A connector 33% |
|
| SD3pin 10 | Connected to: A connector 22% · not connected 44% |
|
| SC3pin 11 | Connected to: A connector 22% · not connected 44% |
|
| GNDpin 12 | Connected to: GND 100% | — |
| SD6pin 17 | Connected to: Not connected 78% | — |
| SC6pin 18 | Connected to: Not connected 78% | — |
| SD7pin 19 | Connected to: Not connected 67% · a signal 22% | — |
| SC7pin 20 | Connected to: Not connected 67% · a signal 22% | — |
| A2pin 21 | Connected to: GND 67% · a signal 33% | — |
| SCLpin 22 | Connected to: The microcontroller 56%, a connector 22% |
|
| SDApin 23 | Connected to: The microcontroller 56%, a connector 22% |
|
| VCCpin 24 | Connected to: 3.3V 100% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Chu Pico Main by whowechina, 4ch-RF-FE by JohnnyGOX17, OVHD Mainboard by stefanofinetti and MF RMP Panel by stefanofinetti.
The PCA9548APW in open source designs
The gallery holds 9 open source boards using the PCA9548APW from 9 GitHub repositories; a typical one measures about 137 × 92.5 mm and carries around 109 components.
56% are two-layer designs, the rest use four layers or more, and 56% carry an open source license.
The most starred is Chu Pico Main by whowechina.
Parts used alongside the PCA9548APW
Microcontrollers on boards using the PCA9548APW
What boards using the PCA9548APW are built for
PCA9548APW: common questions
Where can I find a PCA9548APW reference design?
Each of the 9 boards on this page is a real design using the PCA9548APW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCA9548APW SD0 pin?
The SD0 pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 1.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the PCA9548APW.
What pull-up resistor is used on the PCA9548APW SC0 pin?
The SC0 pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 1.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the PCA9548APW.
What pull-up resistor is used on the PCA9548APW SCL pin?
The SCL pin has a pull-up to 3.3V on 6 of 9 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 9 open source designs using the PCA9548APW.
What parts are used alongside the PCA9548APW?
The AMS1117-3.3, CH340G, CP2102-GMR and XC6220B331MR-G appear in the most repositories here.
Which microcontrollers do boards using the PCA9548APW use?
Most are built on AVR/Arduino (3) and ESP32 (3).
How big is a typical board using the PCA9548APW?
The median is 137 × 92.5 mm, and 56% are two-layer designs.
What is the most popular open source board using the PCA9548APW?
By GitHub stars, Chu Pico Main by whowechina, with 191 stars.
Can I simulate one of these boards using the PCA9548APW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.