13 open source boards using the RN2483
Real designs built with the RN2483, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Lofence
kiu
78 × 130 mm57 parts2LMIT141AVR/Arduino
Ttntrackernode
ttnmapper
48 × 75 mm82 parts2LNo license13Hardware
gfroerli
56 × 90 mm37 parts2LNo license1AVR/Arduino
Cosmonode
exostic
59.7 × 36.2 mm47 parts2LNo license0AVR/Arduino
Smart-Garbage-Collection
cs684-2018
100.1 × 54.7 mm38 parts2LNo license0AVR/Arduino
BUENO-Gas-Sensor
MOSH-Insa-Toulouse
70.1 × 79 mm34 parts2LNo license0Microchip SAM
FLWSB-SAMDaaNo21
DaanDekoningKrekels
85.7 × 21 mm32 parts4LNo license0AVR/Arduino
TP MOSH CapGaz
MOSH-Insa-Toulouse
68.6 × 53.3 mm21 parts2LNo license0AVR/Arduino
Cosmonode ext06
exostic
30.5 × 34.3 mm28 parts2LNo license0AVR/Arduino
V1
MOSH-Insa-Toulouse
68.6 × 53.3 mm21 parts2LNo license0AVR/Arduino
RN2483shield
MOSH-Insa-Toulouse
68.9 × 53.6 mm8 parts2LNo license0AVR/Arduino
Cosmonode ext 04
exostic
25.4 × 34.3 mm25 parts2LNo license0Raspberry Pi
Communications Module
Safecast
33.6 × 65.2 mm22 parts2LCustom license2
How designs wire the RN2483
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the RN2483 connects to, and the resistors, capacitors and other passives placed on it.
- The RESERVED_1 pin is left unconnected on 8 of 9 designs.
- The UART_CTS pin is left unconnected on 7 of 9 designs (a signal on 2).
- The UART_RTS pin is left unconnected on 6 of 9 designs (a signal on 3).
- The RESERVED_2 pin is left unconnected on 6 of 9 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 80% | — |
| UART_RTSpin 2 | Connected to: Not connected 67% · a signal 33% | — |
| UART_CTSpin 3 | Connected to: Not connected 78% · a signal 22% | — |
| RESERVED_1pin 4 | Connected to: Not connected 89% | — |
| RESERVED_2pin 5 | Connected to: Not connected 67% · a signal 33% | — |
| GND_2pin 8 | Connected to: GND 100% | — |
| GPIO13pin 9 | Connected to: Not connected 86% | — |
| GPIO12pin 10 | Connected to: Not connected 86% | — |
| GND_3pin 11 | Connected to: GND 100% | — |
| VDD_1pin 12 | Connected to: 3.3V 75% · a signal 25% |
|
| GPIO11pin 13 | Connected to: Not connected 86% | — |
| GPIO10pin 14 | Connected to: Not connected 86% | — |
| NC_1pin 15 | Connected to: Not connected 86% | — |
| NC_2pin 16 | Connected to: Not connected 86% | — |
| NC_3pin 17 | Connected to: Not connected 86% | — |
| NC_4pin 18 | Connected to: Not connected 86% | — |
| NC_5pin 19 | Connected to: Not connected 86% | — |
| GND_4pin 20 | Connected to: GND 100% | — |
| GND_5pin 21 | Connected to: GND 100% | — |
| GND_6pin 22 | Connected to: GND 100% | — |
| GND_7pin 24 | Connected to: GND 100% | — |
| GND_8pin 26 | Connected to: GND 100% | — |
| GND_9pin 27 | Connected to: GND 100% | — |
| GND_10pin 28 | Connected to: GND 100% | — |
| NC_6pin 29 | Connected to: Not connected 86% | — |
| GND_11pin 33 | Connected to: GND 100% | — |
| VDD_2pin 34 | Connected to: 3.3V 63% · a signal 25% | — |
| GPIO0pin 35 | Connected to: Not connected 71% · a signal 29% | — |
| GPIO1pin 36 | Connected to: Not connected 86% | — |
| GPIO2pin 37 | Connected to: Not connected 86% | — |
| GPIO3pin 38 | Connected to: Not connected 86% | — |
| GPIO4pin 39 | Connected to: Not connected 86% | — |
| GPIO5pin 40 | Connected to: Not connected 86% | — |
| GND_12pin 41 | Connected to: GND 100% | — |
| NC_7pin 42 | Connected to: Not connected 86% | — |
| GPIO6pin 43 | Connected to: Not connected 86% | — |
| GPIO7pin 44 | Connected to: Not connected 86% | — |
| GPIO8pin 45 | Connected to: Not connected 86% | — |
| GPIO9pin 46 | Connected to: Not connected 86% | — |
| GND_13pin 47 | Connected to: GND 100% | — |
7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lofence by kiu, Ttntrackernode by ttnmapper, Communications Module by Safecast and Hardware by gfroerli.
The RN2483 in open source designs
The gallery holds 13 open source boards using the RN2483 from 10 GitHub repositories; a typical one measures about 68.6 × 53.6 mm and carries around 32 components.
92% are two-layer designs, the rest use four layers or more, and 8% carry an open source license.
The most starred is Lofence by kiu.
Parts used alongside the RN2483
Microcontrollers on boards using the RN2483
What boards using the RN2483 are built for
RN2483: common questions
Where can I find a RN2483 reference design?
Each of the 13 boards on this page is a real design using the RN2483. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the RN2483 RESERVED_1 pin connected?
The RESERVED_1 pin is left unconnected on 8 of 9 designs. Counted from the KiCad layouts of 10 open source designs using the RN2483.
How is the RN2483 UART_CTS pin connected?
The UART_CTS pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 10 open source designs using the RN2483.
How is the RN2483 UART_RTS pin connected?
The UART_RTS pin is left unconnected on 6 of 9 designs (a signal on 3). Counted from the KiCad layouts of 10 open source designs using the RN2483.
Which microcontrollers do boards using the RN2483 use?
Most are built on AVR/Arduino (10), Raspberry Pi (1) and Microchip SAM (1).
How big is a typical board using the RN2483?
The median is 68.6 × 53.6 mm, and 92% are two-layer designs.
What is the most popular open source board using the RN2483?
By GitHub stars, Lofence by kiu, with 141 stars.
Can I simulate one of these boards using the RN2483 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.