13 open source boards using the TCA8418
Real designs built with the TCA8418, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Omote
OMOTE-Community
192.4 × 50 mm135 parts2LGPL-3.0153STM32
Printalyzer - Main Board
dektronics
188 × 110 mm136 parts4LNo license37I2c thumb keyboard
AnthonyDiGirolamo
97.2 × 81.3 mm81 parts2LMIT30Keypad
soupie-62
99.1 × 59.7 mm106 partsGPL-3.03RP2040/RP2350
Midi controller
Tommie1236
100 × 100 mm515 parts4LCERN-OHL-W-2.02RP2040/RP2350
Sisyphus
Plajta
52 × 42 mm55 parts2LCustom license1Mct2 buttons
ctcl-bregis
61 × 28 mm32 parts2LNo license1ESP32
Omote
KlausMu
192.4 × 50 mm135 parts2LGPL-3.00ESP32
Ti92revive
ccadic
205 × 113.6 mm88 parts2LNo license49Nestronic Input Board
dkonigsberg
101.6 × 38.1 mm16 parts2LNo license38ESP32
ESP32-T7S3-ControlStand
RobertPHeller
199.4 × 126.4 mm139 parts2LGPL-3.03Keypad
Tommie1236
120 × 189 mm76 parts2LCERN-OHL-W-2.02ESP32
ESP32-S3-WROOM-ControlStand
RobertPHeller
127 × 118.9 mm84 parts2LGPL-3.03
How designs wire the TCA8418
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the TCA8418 connects to, and the resistors, capacitors and other passives placed on it.
- The RESET pin has a pull-up to 3.3V on 10 of 11 designs, most often 10 kΩ (then 4.7 kΩ).
- The VCC pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 1 µF).
- The INT pin has a pull-up to 3.3V on 9 of 11 designs, most often 10 kΩ (then 4.7 kΩ).
- The SDA pin has a pull-up to 3.3V on 7 of 11 designs, most often 4.7 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 19 | Connected to: GND 91% | — |
| RESETpin 20 | Connected to: A connector 27% |
|
| VCCpin 21 | Connected to: 3.3V 100% |
|
| SDApin 22 | Connected to: A connector 55%, the microcontroller 36% |
|
| SCLpin 23 | Connected to: A connector 55%, the microcontroller 36% |
|
| INTpin 24 | Connected to: The microcontroller 36%, a connector 36% |
|
| PADpin 25 | Connected to: Not connected 60% · GND 40% | — |
18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Omote by OMOTE-Community, Ti92revive by ccadic, Nestronic Input Board by dkonigsberg and Printalyzer - Main Board by dektronics.
The TCA8418 in open source designs
The gallery holds 13 open source boards using the TCA8418 from 11 GitHub repositories; a typical one measures about 120 × 81.3 mm and carries around 88 components.
83% are two-layer designs, the rest use four layers or more, and 62% carry an open source license.
The most starred is Omote by OMOTE-Community.
Parts used alongside the TCA8418
Microcontrollers on boards using the TCA8418
What boards using the TCA8418 are built for
TCA8418: common questions
Where can I find a TCA8418 reference design?
Each of the 13 boards on this page is a real design using the TCA8418. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TCA8418 RESET pin?
The RESET pin has a pull-up to 3.3V on 10 of 11 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 11 open source designs using the TCA8418.
What decoupling capacitors do designs use on the TCA8418 VCC pin?
The VCC pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 11 open source designs using the TCA8418.
What pull-up resistor is used on the TCA8418 INT pin?
The INT pin has a pull-up to 3.3V on 9 of 11 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 11 open source designs using the TCA8418.
What parts are used alongside the TCA8418?
The USBLC6-2P6, AP2112K-3.3, CH340C, DW01A and ESP32-S3-WROOM-1-N16R8 appear in the most repositories here.
Which microcontrollers do boards using the TCA8418 use?
Most are built on ESP32 (5), RP2040/RP2350 (2) and STM32 (1).
How big is a typical board using the TCA8418?
The median is 120 × 81.3 mm, and 83% are two-layer designs.
What is the most popular open source board using the TCA8418?
By GitHub stars, Omote by OMOTE-Community, with 153 stars.
Can I simulate one of these boards using the TCA8418 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.