7 open source boards using the TCMT1107
Real designs built with the TCMT1107, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
IO-SDR
rishivg
99.4 × 60 mm309 parts8LCERN-OHL-S-2.010FPGA
IO SDR 1.1
SunnyYoshimitsu
91.5 × 91.5 mm268 parts6LNo license3Synchronous Flyback Converter - Evaluation Board
crawford
88.9 × 46.4 mm92 parts2LGPL-3.03STM32
OpenWeatherStation
VitalSeptfonds
50 × 100 mm107 parts2LMIT2EDL Project 2026
segf4u1t-139
182 × 126.2 mm237 parts2LNo license0Fuente-12v
brunogle
154 × 85 mm55 parts2LNo license0Silicon Labs
Chassis
crawford
60.3 × 52.7 mm86 parts2LGPL-3.03
How designs wire the TCMT1107
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TCMT1107 connects to, and the resistors, capacitors and other passives placed on it.
- The TIMER pin is tied to GND on 5 of 6 designs.
- The EN pin has a series resistor on 4 of 6 designs, most often 1 kΩ (then 390 Ω).
- The GND pin has a series resistor on 4 of 6 designs, most often 2 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PGBpin 1 | Connected to: Signal 83% · 12V 17% |
|
| ENpin 2 | Connected to: Signal 100% |
|
| TIMERpin 3 | Connected to: GND 83% · a signal 17% | — |
| GNDpin 4 | Connected to: A connector 50% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include IO-SDR by rishivg, Chassis by crawford, IO SDR 1.1 by SunnyYoshimitsu and OpenWeatherStation by VitalSeptfonds.
The TCMT1107 in open source designs
The gallery holds 7 open source boards using the TCMT1107 from 6 GitHub repositories; a typical one measures about 91.5 × 85 mm and carries around 107 components.
71% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is IO-SDR by rishivg.
Parts used alongside the TCMT1107
Microcontrollers on boards using the TCMT1107
What boards using the TCMT1107 are built for
TCMT1107: common questions
Where can I find a TCMT1107 reference design?
Each of the 7 boards on this page is a real design using the TCMT1107. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TCMT1107 TIMER pin connected?
The TIMER pin is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TCMT1107.
What resistor goes on the TCMT1107 EN pin?
The EN pin has a series resistor on 4 of 6 designs, most often 1 kΩ (then 390 Ω). Counted from the KiCad layouts of 6 open source designs using the TCMT1107.
What resistor goes on the TCMT1107 GND pin?
The GND pin has a series resistor on 4 of 6 designs, most often 2 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the TCMT1107.
What parts are used alongside the TCMT1107?
The BNO085, H5TQ4G63AFR, MS5611-01BA, MX25U1635EZNI-10G and RT9193-33B appear in the most repositories here.
Which microcontrollers do boards using the TCMT1107 use?
Most are built on FPGA (2), Silicon Labs (1) and STM32 (1).
How big is a typical board using the TCMT1107?
The median is 91.5 × 85 mm, and 71% are two-layer designs.
What is the most popular open source board using the TCMT1107?
By GitHub stars, IO-SDR by rishivg, with 10 stars.
Can I simulate one of these boards using the TCMT1107 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.