21 open source boards using the SY6280AAC

Real designs built with the SY6280AAC, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the SY6280AAC

Read from the KiCad layouts of 20 open source designs, one per repository: what each pin of the SY6280AAC connects to, and the resistors, capacitors and other passives placed on it.

  • The ISET pin has a resistor to GND on 20 of 20 designs, most often 6.8 kΩ (then 10 kΩ).
  • The IN pin is tied to 5V on 17 of 20 designs (a signal on 3).
  • The OUT pin is tied to 5V on 14 of 20 designs (a signal on 6).
  • The ON pin has a resistor to GND on 11 of 20 designs, most often 100 kΩ (then 10 kΩ).
OUTpin 1Connected to: 5V 70% · a signal 30%
GNDpin 2Connected to: GND 100%
ISETpin 3Connected to: Signal 100%
  • Resistor to GND on 100% · 6.8 kΩ (7), 10 kΩ (4), 5.1 kΩ (3)
ONpin 4Connected to: The microcontroller 30% · 5V 25%
  • Resistor to GND on 55% · 100 kΩ (5), 10 kΩ (4), 5.1 kΩ (1)
INpin 5Connected to: 5V 85% · a signal 15%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Anyon e motherboard by byrantech, OtterCastAudioV2 by Ottercast, Icepi sbc by cheyao and IO-SDR by rishivg.

The SY6280AAC in open source designs

The gallery holds 21 open source boards using the SY6280AAC from 20 GitHub repositories; a typical one measures about 90.4 × 64.3 mm and carries around 124 components.

81% use four copper layers or more, and 62% carry an open source license.

The most starred is Anyon e motherboard by byrantech.

Microcontrollers on boards using the SY6280AAC

What boards using the SY6280AAC are built for

SY6280AAC: common questions

Where can I find a SY6280AAC reference design?

Each of the 21 boards on this page is a real design using the SY6280AAC. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the SY6280AAC ISET pin?

The ISET pin has a resistor to GND on 20 of 20 designs, most often 6.8 kΩ (then 10 kΩ). Counted from the KiCad layouts of 20 open source designs using the SY6280AAC.

How is the SY6280AAC IN pin connected?

The IN pin is tied to 5V on 17 of 20 designs (a signal on 3). Counted from the KiCad layouts of 20 open source designs using the SY6280AAC.

How is the SY6280AAC OUT pin connected?

The OUT pin is tied to 5V on 14 of 20 designs (a signal on 6). Counted from the KiCad layouts of 20 open source designs using the SY6280AAC.

What parts are used alongside the SY6280AAC?

The USBLC6-2SC6, CH334R, SK6805, SY8089AAAC and TPS63020DSJR appear in the most repositories here.

Which microcontrollers do boards using the SY6280AAC use?

Most are built on ESP32 (5), RP2040/RP2350 (2), FPGA (2) and WCH CH32/CH55x (2).

How big is a typical board using the SY6280AAC?

The median is 90.4 × 64.3 mm, and 19% are two-layer designs.

What is the most popular open source board using the SY6280AAC?

By GitHub stars, Anyon e motherboard by byrantech, with 4,264 stars.

Can I simulate one of these boards using the SY6280AAC before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part