5 open source boards using the TP5400
Real designs built with the TP5400, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
M5Pi-F1C100S/200S
imliubo
47.5 × 50 mm141 parts4LNo license197Ecad viewer
Huaqiu-Electronics
47.5 × 50 mm141 parts4LMIT91ESP32
Joker60 mkII
ZeshuLiu
323.5 × 102.5 mm193 parts2LMIT0RP2040/RP2350
Brique
tommy-gilligan
42.1 × 107.7 mm84 parts4LMIT0Lichee-Jack EXT. Board
KaliAssistant
45.6 × 28 mm35 parts4LGPL-3.05
How designs wire the TP5400
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TP5400 connects to, and the resistors, capacitors and other passives placed on it.
- The VOUT pin has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 47 µF).
- The PROG pin has a resistor to GND on 5 of 5 designs, most often 1.1 kΩ (then 5 kΩ).
- The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 22 µF).
- The LX pin has a inductor on 5 of 5 designs, most often 10 µH (then 4.7 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTpin 1 | Connected to: Signal 60% · 5V 40% |
|
| PROGpin 3 | Connected to: Signal 100% |
|
| VCCpin 5 | Connected to: 5V 60% · a signal 40% |
|
| BATpin 6 | Connected to: VBAT 40% · GND 20% · a signal 40% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| LXpin 8 | Connected to: Signal 100% |
|
| EPpin 9 | Connected to: Not connected 67% · GND 33% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include M5Pi-F1C100S/200S by imliubo, Ecad viewer by Huaqiu-Electronics, Lichee-Jack EXT. Board by KaliAssistant and Brique by tommy-gilligan.
The TP5400 in open source designs
The gallery holds 5 open source boards using the TP5400 from 5 GitHub repositories; a typical one measures about 47.5 × 50 mm and carries around 141 components.
80% use four copper layers or more, and 80% carry an open source license.
The most starred is M5Pi-F1C100S/200S by imliubo.
Parts used alongside the TP5400
Microcontrollers on boards using the TP5400
What boards using the TP5400 are built for
TP5400: common questions
Where can I find a TP5400 reference design?
Each of the 5 boards on this page is a real design using the TP5400. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TP5400 VOUT pin connected?
The VOUT pin has a capacitor to GND on 5 of 5 designs, most often 100 nF (then 47 µF). Counted from the KiCad layouts of 5 open source designs using the TP5400.
What resistor goes on the TP5400 PROG pin?
The PROG pin has a resistor to GND on 5 of 5 designs, most often 1.1 kΩ (then 5 kΩ). Counted from the KiCad layouts of 5 open source designs using the TP5400.
What decoupling capacitors do designs use on the TP5400 VCC pin?
The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the TP5400.
What parts are used alongside the TP5400?
The CH340E, ESP8089, F1C100s, MPU-6050 and NS4158B appear in the most repositories here.
Which microcontrollers do boards using the TP5400 use?
Most are built on ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the TP5400?
The median is 47.5 × 50 mm, and 20% are two-layer designs.
What is the most popular open source board using the TP5400?
By GitHub stars, M5Pi-F1C100S/200S by imliubo, with 197 stars.
Can I simulate one of these boards using the TP5400 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.