8 open source boards using the TPL5010
Real designs built with the TPL5010, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
EPS
rgw3d
85 × 85 mm629 parts4LGPL-3.0157- schematic only · 15 partsAVR/Arduino
Kicad firmware generation
DLR-RY
15 partsMIT26 Hardware watchdog
rmingon
17.8 × 25.4 mm13 parts2LNo license2AVR/Arduino
Mobile Monitor Redesign
deogratius2phantom
49 × 39.1 mm90 parts4LNo license0ESP32
Pcb one
Open-Air-Foundation
124.1 × 112 mm48 parts2LCC-BY-SA-4.00ESP32
Pcb openair main
Open-Air-Foundation
4.2 × 19 mm36 parts2LCC-BY-SA-4.00STM32
Sun sensor test
rgw3d
132.7 × 37.3 mm151 parts2LGPL-3.0157STM32
AVIONICS BOARD
rgw3d
85 × 85 mm132 parts4LGPL-3.0157
How designs wire the TPL5010
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPL5010 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 1 µF).
- The DELAY/M_RST pin has a resistor to GND on 4 of 5 designs, most often 51 kΩ (then 8.85 kΩ).
- The RST pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ (then 100 kΩ).
- The RST pin has a capacitor to GND on 2 of 5 designs, most often 1 µF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 80% · a signal 20% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| DELAY/M_RSTpin 3 | Connected to: Signal 100% |
|
| RSTpin 6 | Connected to: The microcontroller 40% · not connected 20% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AVIONICS BOARD by rgw3d, Hardware watchdog by rmingon, Mobile Monitor Redesign by deogratius2phantom and Pcb one by Open-Air-Foundation.
The TPL5010 in open source designs
The gallery holds 8 open source boards using the TPL5010 from 6 GitHub repositories; a typical one measures about 85 × 39.1 mm and carries around 69 components.
57% are two-layer designs, the rest use four layers or more, and 75% carry an open source license.
The most starred is EPS by rgw3d.
Parts used alongside the TPL5010
Microcontrollers on boards using the TPL5010
What boards using the TPL5010 are built for
TPL5010: common questions
Where can I find a TPL5010 reference design?
Each of the 8 boards on this page is a real design using the TPL5010. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TPL5010 VDD pin?
The VDD pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the TPL5010.
What resistor goes on the TPL5010 DELAY/M_RST pin?
The DELAY/M_RST pin has a resistor to GND on 4 of 5 designs, most often 51 kΩ (then 8.85 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPL5010.
What pull-up resistor is used on the TPL5010 RST pin?
The RST pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPL5010.
Which microcontrollers do boards using the TPL5010 use?
Most are built on STM32 (3), AVR/Arduino (2) and ESP32 (2).
How big is a typical board using the TPL5010?
The median is 85 × 39.1 mm, and 57% are two-layer designs.
What is the most popular open source board using the TPL5010?
By GitHub stars, EPS by rgw3d, with 157 stars.
Can I simulate one of these boards using the TPL5010 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.