7 open source boards using the TPS2115APWR
Real designs built with the TPS2115APWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Liquid-Engine-Controller
SunDevilRocketry
116.8 × 56.7 mm114 parts4LNo license1ESP32
Main board v3
BlueJayRacing
85 × 73 mm113 parts4LNo license0RP2040/RP2350
4in gps
sonicavionics
84.1 × 61.7 mm84 parts4LMIT0ESP32
Digital
dwynnychuk
60 × 80 mm82 parts4LNo license0Smartwatch
JitDey2004
45 × 41 mm67 parts4LGPL-3.00Osw light
Monacrylic
36.1 × 36.1 mm51 parts4LNo license2X osw light
Monacrylic
36.1 × 36.1 mm51 parts4LNo license2
How designs wire the TPS2115APWR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS2115APWR connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 6 of 6 designs, most often 510 Ω (then 470 Ω).
- The IN2 pin is tied to VBUS on 6 of 6 designs.
- The D1 pin is tied to GND on 5 of 6 designs.
- The OUT pin is tied to VCC on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| STATpin 1 | Connected to: Ttgo-32-micro 33% · not connected 17% · 5V 17% |
|
| D0pin 2 | Connected to: Not connected 50% · GND 17% · VBAT 33% |
|
| D1pin 3 | Connected to: GND 83% · 5V 17% | — |
| ILIMpin 4 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| IN2pin 6 | Connected to: VBUS 100% | — |
| OUTpin 7 | Connected to: VCC 83% · a signal 17% | — |
| IN1pin 8 | Connected to: VBAT 83% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Osw light by Monacrylic, Liquid-Engine-Controller by SunDevilRocketry, Main board v3 by BlueJayRacing and DigitalPCB by dwynnychuk.
The TPS2115APWR in open source designs
The gallery holds 7 open source boards using the TPS2115APWR from 6 GitHub repositories; a typical one measures about 60 × 56.7 mm and carries around 82 components.
100% use four copper layers or more, and 29% carry an open source license.
The most starred is Osw light by Monacrylic.
Parts used alongside the TPS2115APWR
Microcontrollers on boards using the TPS2115APWR
What boards using the TPS2115APWR are built for
TPS2115APWR: common questions
Where can I find a TPS2115APWR reference design?
Each of the 7 boards on this page is a real design using the TPS2115APWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2115APWR ILIM pin?
The ILIM pin has a resistor to GND on 6 of 6 designs, most often 510 Ω (then 470 Ω). Counted from the KiCad layouts of 6 open source designs using the TPS2115APWR.
How is the TPS2115APWR IN2 pin connected?
The IN2 pin is tied to VBUS on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TPS2115APWR.
How is the TPS2115APWR D1 pin connected?
The D1 pin is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the TPS2115APWR.
What parts are used alongside the TPS2115APWR?
The BMA400, CH340E, DS3231MZ, GC9A01_IPS_display and MCP73831T-2ACI/OT appear in the most repositories here.
Which microcontrollers do boards using the TPS2115APWR use?
Most are built on ESP32 (2), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TPS2115APWR?
The median is 60 × 56.7 mm, and 0% are two-layer designs.
What is the most popular open source board using the TPS2115APWR?
By GitHub stars, Osw light by Monacrylic, with 2 stars.
Can I simulate one of these boards using the TPS2115APWR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.