8 open source boards using the TPS3700DDCR
Real designs built with the TPS3700DDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Esp32Tap - ESP32-S3 Precor serial bus tap
scottmsilver
95 × 58 mm76 parts4LNo license2FPGA
SN-64
FantomZap
101.8 × 80.5 mm383 parts6LNo license1RP2040/RP2350
PiEBV
Low-Boom
126 × 126 mm82 parts4LGPL-3.01Ham radio
charlieh0tel
76.2 × 69.9 mm34 parts2LMIT1Project ATO / Supervision
pratham-cloud-ctrl
300 × 250 mm479 parts4LCustom license0STM32
Flight-Controller-V1
desanv01
104 × 104 mm310 parts6LCustom license0ACTUATOR SUPPORT BOARD - UNVALIDATED PROTOTYPE
darshp848
180 × 45 mm132 parts2LApache-2.01Project ATO / Power
pratham-cloud-ctrl
175 × 185 mm156 parts4LCustom license0
How designs wire the TPS3700DDCR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS3700DDCR connects to, and the resistors, capacitors and other passives placed on it.
- The OUTA pin has a series resistor on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The INA+ pin has a series resistor on 5 of 7 designs, most often 750 kΩ (then 37.4 kΩ).
- The VDD pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF (then 1 µF).
- The INA+ pin has a resistor to GND on 4 of 7 designs, most often 10 kΩ (then 1 MΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTApin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 86% | — |
| INA+pin 3 | Connected to: Signal 100% |
|
| INB-pin 4 | Connected to: Signal 71% · GND 29% |
|
| VDDpin 5 | Connected to: VIN 57% · a signal 43% |
|
| OUTBpin 6 | Connected to: Signal 71% · not connected 29% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Esp32Tap - ESP32-S3 Precor serial bus tap by scottmsilver, Ham radio by charlieh0tel, ACTUATOR SUPPORT BOARD - UNVALIDATED PROTOTYPE by darshp848 and SN-64 by FantomZap.
The TPS3700DDCR in open source designs
The gallery holds 8 open source boards using the TPS3700DDCR from 7 GitHub repositories; a typical one measures about 115 × 92.3 mm and carries around 144 components.
75% use four copper layers or more, and 38% carry an open source license.
The most starred is Esp32Tap - ESP32-S3 Precor serial bus tap by scottmsilver.
Parts used alongside the TPS3700DDCR
Microcontrollers on boards using the TPS3700DDCR
What boards using the TPS3700DDCR are built for
TPS3700DDCR: common questions
Where can I find a TPS3700DDCR reference design?
Each of the 8 boards on this page is a real design using the TPS3700DDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS3700DDCR OUTA pin?
The OUTA pin has a series resistor on 5 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS3700DDCR.
What resistor goes on the TPS3700DDCR INA+ pin?
The INA+ pin has a series resistor on 5 of 7 designs, most often 750 kΩ (then 37.4 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS3700DDCR.
What decoupling capacitors do designs use on the TPS3700DDCR VDD pin?
The VDD pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 7 open source designs using the TPS3700DDCR.
What parts are used alongside the TPS3700DDCR?
The SN74AXC4T774PWR, SN74LVC1G07DBVR, SN74LVC1G32DBVR, TPS22918DBVR and TPS259470LRPWR appear in the most repositories here.
Which microcontrollers do boards using the TPS3700DDCR use?
Most are built on ESP32 (1), FPGA (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TPS3700DDCR?
The median is 115 × 92.3 mm, and 25% are two-layer designs.
What is the most popular open source board using the TPS3700DDCR?
By GitHub stars, Esp32Tap - ESP32-S3 Precor serial bus tap by scottmsilver, with 2 stars.
Can I simulate one of these boards using the TPS3700DDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.