10 open source boards using the VN7007ALH
Real designs built with the VN7007ALH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ChainlinkDriverTester
scottbez1
198.1 × 95.3 mm123 parts2LApache-2.04.2kChainlinkDriverTester
rossbb
198.1 × 95.3 mm123 parts2LApache-2.00ChainlinkDriverTester
kiwonbyun
198.1 × 95.3 mm123 parts2LApache-2.00ChainlinkDriverTester
nintando64
198.1 × 95.3 mm123 parts2LApache-2.00ChainlinkDriverTester
orgTestCodacy11KRepos110MB
198.1 × 95.3 mm123 parts2LApache-2.00ChainlinkBase
scottbez1
98.4 × 190.5 mm119 parts2LApache-2.04.2kChainlinkBase
orgTestCodacy11KRepos110MB
98.4 × 190.5 mm119 parts2LApache-2.00ChainlinkBase
rossbb
98.4 × 190.5 mm119 parts2LApache-2.00ChainlinkBase
nintando64
98.4 × 190.5 mm119 parts2LApache-2.00ChainlinkBase
kiwonbyun
98.4 × 190.5 mm119 parts2LApache-2.00
How designs wire the VN7007ALH
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the VN7007ALH connects to, and the resistors, capacitors and other passives placed on it.
- Pin 4 has a series resistor on 5 of 5 designs, most often 15 kΩ.
- Pin 5 has a resistor to GND on 5 of 5 designs, most often 1 kΩ.
- Pin 6 has a resistor to GND on 5 of 5 designs, most often 15 kΩ.
- Pin TAB has a capacitor to GND on 5 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 4 | Connected to: Signal 100% |
|
| Pin 5 | Connected to: Signal 100% |
|
| Pin 6 | Connected to: Signal 100% |
|
| Pin 7 | Connected to: GND 100% | — |
| Pin TAB | Connected to: INA219BxD 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ChainlinkBase by scottbez1, ChainlinkBase by kiwonbyun, ChainlinkBase by nintando64 and ChainlinkBase by orgTestCodacy11KRepos110MB.
The VN7007ALH in open source designs
The gallery holds 10 open source boards using the VN7007ALH from 5 GitHub repositories; a typical one measures about 148.3 × 142.9 mm and carries around 121 components.
100% are two-layer designs, the rest use four layers or more, and 100% carry an open source license.
The most starred is ChainlinkDriverTester by scottbez1.
Parts used alongside the VN7007ALH
What boards using the VN7007ALH are built for
VN7007ALH: common questions
Where can I find a VN7007ALH reference design?
Each of the 10 boards on this page is a real design using the VN7007ALH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the VN7007ALH pin 4?
Pin 4 has a series resistor on 5 of 5 designs, most often 15 kΩ. Counted from the KiCad layouts of 5 open source designs using the VN7007ALH.
What resistor goes on the VN7007ALH pin 5?
Pin 5 has a resistor to GND on 5 of 5 designs, most often 1 kΩ. Counted from the KiCad layouts of 5 open source designs using the VN7007ALH.
What resistor goes on the VN7007ALH pin 6?
Pin 6 has a resistor to GND on 5 of 5 designs, most often 15 kΩ. Counted from the KiCad layouts of 5 open source designs using the VN7007ALH.
What parts are used alongside the VN7007ALH?
The AP7361C-33E, Buck, INA219BxD, LM7805_TO220 and MCP23017_SS appear in the most repositories here.
How big is a typical board using the VN7007ALH?
The median is 148.3 × 142.9 mm, and 100% are two-layer designs.
What is the most popular open source board using the VN7007ALH?
By GitHub stars, ChainlinkDriverTester by scottbez1, with 4,156 stars.
Can I simulate one of these boards using the VN7007ALH before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.