34 open source boards using the Wio-SX1262

Real designs built with the Wio-SX1262, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

34 boardsClear filters|Most starred

How designs wire the Wio-SX1262

Read from the KiCad layouts of 20 open source designs, one per repository: what each pin of the Wio-SX1262 connects to, and the resistors, capacitors and other passives placed on it.

  • The MISO pin has a series resistor on 16 of 20 designs, most often 47 Ω (then 0 Ω).
  • The MOSI pin has a series resistor on 16 of 20 designs, most often 47 Ω (then 0 Ω).
  • The ANT pin is left unconnected on 19 of 20 designs.
  • The SCK pin has a series resistor on 15 of 20 designs, most often 47 Ω (then 22 Ω).
MISOpin 2Connected to: Signal 100%
  • Series resistor on 80% · 47 Ω (14), 0 Ω (2), 22 Ω (1)
MOSIpin 3Connected to: Signal 100%
  • Series resistor on 80% · 47 Ω (14), 0 Ω (2), 22 Ω (1)
SCKpin 4Connected to: Signal 100%
  • Series resistor on 75% · 47 Ω (14), 22 Ω (1)
RSTpin 5Connected to: A connector 80%
  • Pull-up to 3.3V on 75% · 10 kΩ (15)
NSSpin 6Connected to: Signal 100%
  • Series resistor on 75% · 47 Ω (14), 22 Ω (1)
GND1pin 7Connected to: GND 100%
VCCpin 8Connected to: 3.3V 100%
ANTpin 9Connected to: Not connected 95%
GND2pin 10Connected to: GND 100%

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LIA by JGAguado, Wio-SX1262 for XIAO nRF52840 by Josephrp, Wio-SX1262 for ESP32S3 by dhirptl and Wio-SX1262 for ESP32S3 by Videocraft10.

The Wio-SX1262 in open source designs

The gallery holds 34 open source boards using the Wio-SX1262 from 20 GitHub repositories; a typical one measures about 17.8 × 21.4 mm and carries around 14 components.

97% are two-layer designs, the rest use four layers or more, and 32% carry an open source license.

The most starred is LIA by JGAguado.

Microcontrollers on boards using the Wio-SX1262

Wio-SX1262: common questions

Where can I find a Wio-SX1262 reference design?

Each of the 34 boards on this page is a real design using the Wio-SX1262. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the Wio-SX1262 MISO pin?

The MISO pin has a series resistor on 16 of 20 designs, most often 47 Ω (then 0 Ω). Counted from the KiCad layouts of 20 open source designs using the Wio-SX1262.

What resistor goes on the Wio-SX1262 MOSI pin?

The MOSI pin has a series resistor on 16 of 20 designs, most often 47 Ω (then 0 Ω). Counted from the KiCad layouts of 20 open source designs using the Wio-SX1262.

How is the Wio-SX1262 ANT pin connected?

The ANT pin is left unconnected on 19 of 20 designs. Counted from the KiCad layouts of 20 open source designs using the Wio-SX1262.

Which microcontrollers do boards using the Wio-SX1262 use?

Most are built on ESP32 (2) and STM32 (1).

How big is a typical board using the Wio-SX1262?

The median is 17.8 × 21.4 mm, and 97% are two-layer designs.

What is the most popular open source board using the Wio-SX1262?

By GitHub stars, LIA by JGAguado, with 15 stars.

Can I simulate one of these boards using the Wio-SX1262 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part