11 open source boards using the XC9536PC44
Real designs built with the XC9536PC44, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FellaPC
agkaminski
284.9 × 96.5 mm107 parts2LCC0-1.02Z80-MegaMapper
tergav17
158.8 × 91.4 mm42 parts2LNo license1VT100
Roland-Scholz
99.1 × 99.1 mm33 parts2LNo license1Zak180
agkaminski
188 × 128.3 mm128 parts4LCC-BY-NC-4.00AVR/Arduino
Vga
agkaminski
129.5 × 74.2 mm36 parts2LNo license1GfxV9990
ddraig68k
100 × 100 mm70 parts4LMIT29VT100 MCU
Roland-Scholz
100.3 × 100.3 mm25 parts2LNo license1AudioSID
ddraig68k
100 × 100 mm69 parts4LMIT29GfxTMS9918
ddraig68k
100 × 100 mm33 parts4LMIT29Eth8019
ddraig68k
100 × 62.5 mm30 parts4LMIT29JoypadController
ddraig68k
100 × 100 mm30 parts2LMIT29
How designs wire the XC9536PC44
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the XC9536PC44 connects to, and the resistors, capacitors and other passives placed on it.
- The I/O/GCK1 pin has a crystal on 4 of 6 designs, most often 25.175 MHz.
- The I/O/GSR pin has a pull-up to VCC on 3 of 6 designs, most often 1 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| I/O/GCK1pin 5 | Connected to: 74HC166 50%, a connector 33%, 74HC174 33% |
|
| GNDpin 10, 23, 31 | Connected to: GND 100% | — |
| VCCpin 21, 41 | Connected to: 5V 100% | — |
| VCCIOpin 32 | Connected to: 5V 100% | — |
| I/O/GSRpin 39 | Connected to: A connector 33% · not connected 17% |
|
23 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AudioSID by ddraig68k, FellaPC by agkaminski, Vga by agkaminski and VT100 by Roland-Scholz.
The XC9536PC44 in open source designs
The gallery holds 11 open source boards using the XC9536PC44 from 6 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 36 components.
55% are two-layer designs, the rest use four layers or more, and 55% carry an open source license.
The most starred is GfxV9990 by ddraig68k.
Parts used alongside the XC9536PC44
Microcontrollers on boards using the XC9536PC44
What boards using the XC9536PC44 are built for
XC9536PC44: common questions
Where can I find a XC9536PC44 reference design?
Each of the 11 boards on this page is a real design using the XC9536PC44. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the XC9536PC44 I/O/GCK1 pin connected?
The I/O/GCK1 pin has a crystal on 4 of 6 designs, most often 25.175 MHz. Counted from the KiCad layouts of 6 open source designs using the XC9536PC44.
What pull-up resistor is used on the XC9536PC44 I/O/GSR pin?
The I/O/GSR pin has a pull-up to VCC on 3 of 6 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the XC9536PC44.
What parts are used alongside the XC9536PC44?
The 2764, 6264, 74HC02, 74HC166 and 74HC245 appear in the most repositories here.
Which microcontrollers do boards using the XC9536PC44 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the XC9536PC44?
The median is 100 × 100 mm, and 55% are two-layer designs.
What is the most popular open source board using the XC9536PC44?
By GitHub stars, GfxV9990 by ddraig68k, with 29 stars.
Can I simulate one of these boards using the XC9536PC44 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.