7 open source boards using the YM3012
Real designs built with the YM3012, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
YM2151 VGM STM32
AidanHockey5
156.9 × 67.3 mm52 parts2LAGPL-3.081AVR/Arduino
OtterX
RetroRemake
170.1 × 170.1 mm168 parts4LCERN-OHL-W-2.040Microchip SAM
YM2151 Arcade Classic 2
AidanHockey5
99 × 99 mm111 parts4LAGPL-3.022Rc2014-ym2151
electrified
100 × 50 mm27 parts2LNo license9AVR/Arduino
Z80 YM2151
kuninet
100 × 75 mm36 parts2LMIT5YM2151 VGM STM32
cas70240
156.9 × 67.3 mm52 parts2LAGPL-3.00AudioYM2151
ddraig68k
100 × 100 mm54 parts4LMIT29
How designs wire the YM3012
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the YM3012 connects to, and the resistors, capacitors and other passives placed on it.
- The CH2 pin has a capacitor to GND on 7 of 7 designs, most often 3.3 nF (then 10 nF).
- The CH1 pin has a capacitor to GND on 7 of 7 designs, most often 3.3 nF (then 10 nF).
- The COM pin has a series resistor on 7 of 7 designs, most often 100 Ω (then 560 Ω).
- The RB pin has a capacitor to GND on 6 of 7 designs, most often 10 µF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 5V 86% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| AGNDpin 8, 16 | Connected to: GND 100% | — |
| CH2pin 9 | Connected to: TL064 43% |
|
| CH1pin 10 | Connected to: TL064 43% |
|
| COMpin 11 | Connected to: Signal 100% |
|
| RBpin 15 | Connected to: TL064 43% |
|
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include YM2151 VGM STM32 by AidanHockey5, OtterX by RetroRemake, AudioYM2151 by ddraig68k and YM2151 Arcade Classic 2 by AidanHockey5.
The YM3012 in open source designs
The gallery holds 7 open source boards using the YM3012 from 7 GitHub repositories; a typical one measures about 100 × 75 mm and carries around 52 components.
57% are two-layer designs, the rest use four layers or more, and 86% carry an open source license.
The most starred is YM2151 VGM STM32 by AidanHockey5.
Parts used alongside the YM3012
Microcontrollers on boards using the YM3012
What boards using the YM3012 are built for
YM3012: common questions
Where can I find a YM3012 reference design?
Each of the 7 boards on this page is a real design using the YM3012. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the YM3012 CH2 pin connected?
The CH2 pin has a capacitor to GND on 7 of 7 designs, most often 3.3 nF (then 10 nF). Counted from the KiCad layouts of 7 open source designs using the YM3012.
How is the YM3012 CH1 pin connected?
The CH1 pin has a capacitor to GND on 7 of 7 designs, most often 3.3 nF (then 10 nF). Counted from the KiCad layouts of 7 open source designs using the YM3012.
What resistor goes on the YM3012 COM pin?
The COM pin has a series resistor on 7 of 7 designs, most often 100 Ω (then 560 Ω). Counted from the KiCad layouts of 7 open source designs using the YM3012.
What parts are used alongside the YM3012?
The YM2151, LTC6903, TL064, TPA3122D2 and BluePill_STM32F103C appear in the most repositories here.
Which microcontrollers do boards using the YM3012 use?
Most are built on AVR/Arduino (2) and Microchip SAM (1).
How big is a typical board using the YM3012?
The median is 100 × 75 mm, and 57% are two-layer designs.
What is the most popular open source board using the YM3012?
By GitHub stars, YM2151 VGM STM32 by AidanHockey5, with 81 stars.
Can I simulate one of these boards using the YM3012 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.