7 open source boards using the LD1117
Real designs built with the LD1117, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
YM2151 VGM STM32
AidanHockey5
156.9 × 67.3 mm52 parts2LAGPL-3.081OricMouse
986-Studio
85.1 × 71.1 mm38 parts2LNo license6Prog tool
linuxboot
55 × 26.5 mm70 parts2LGPL-3.04AVR/Arduino
Toadstool-Mega328
CrashBangProto
49.5 × 81.2 mm26 parts2LGPL-3.01YM2151 VGM STM32
cas70240
156.9 × 67.3 mm52 parts2LAGPL-3.00Raspberry Pi
Hat zero brick
Tinkerforge
65 × 30.6 mm40 parts2LNo license0Expander midi
doctea
20 × 128.5 mm44 parts2LNo license0
How designs wire the LD1117
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LD1117 connects to, and the resistors, capacitors and other passives placed on it.
- The VI_3 pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF (then 10 µF).
- The ADJ_1 pin is tied to GND on 5 of 7 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJ_1pin 1 | Connected to: GND 71% · a signal 29% | — |
| VO_2pin 2 | Connected to: 3.3V 71% · a signal 29% | — |
| VI_3pin 3 | Connected to: 5V 57% · a signal 43% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include YM2151 VGM STM32 by AidanHockey5, OricMouse by 986-Studio, Prog tool by linuxboot and Toadstool-Mega328 by CrashBangProto.
The LD1117 in open source designs
The gallery holds 7 open source boards using the LD1117 from 7 GitHub repositories; a typical one measures about 65 × 67.3 mm and carries around 44 components.
100% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is YM2151 VGM STM32 by AidanHockey5.
Parts used alongside the LD1117
Microcontrollers on boards using the LD1117
What boards using the LD1117 are built for
LD1117: common questions
Where can I find a LD1117 reference design?
Each of the 7 boards on this page is a real design using the LD1117. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LD1117 VI_3 pin?
The VI_3 pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 7 open source designs using the LD1117.
How is the LD1117 ADJ_1 pin connected?
The ADJ_1 pin is tied to GND on 5 of 7 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the LD1117.
What parts are used alongside the LD1117?
The BluePill_STM32F103C, CH340G, LM2596S-5.0, LTC6903 and OLED_128x32_I2C appear in the most repositories here.
Which microcontrollers do boards using the LD1117 use?
Most are built on AVR/Arduino (1) and Raspberry Pi (1).
How big is a typical board using the LD1117?
The median is 65 × 67.3 mm, and 100% are two-layer designs.
What is the most popular open source board using the LD1117?
By GitHub stars, YM2151 VGM STM32 by AidanHockey5, with 81 stars.
Can I simulate one of these boards using the LD1117 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.