33 open source boards using the MCP73831T
Real designs built with the MCP73831T, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Makennbot
idlehandsdev
60 × 75 mm53 parts2LNo license175Microchip SAM
POV Fidget
idlehandsdev
71.9 × 65.7 mm66 parts2LNo license54ESP8266
Wifi PB panel
AntonioMR
100 × 100 mm162 parts2LNo license29ESP32
Inkplate10 Soldered
SolderedElectronics
224.8 × 162.4 mm215 parts2LTAPR-OHL-1.018ESP32
Soldered Inkplate 4 TEMPERA with glass panel
SolderedElectronics
72 × 78 mm246 parts4LTAPR-OHL-1.05ESP32
Soldered Inkplate 6
SolderedElectronics
144.4 × 107.8 mm224 parts2LTAPR-OHL-1.05ESP32
Soldered Inkplate 6 MOTION
SolderedElectronics
144.4 × 107.8 mm313 parts2LTAPR-OHL-1.04ESP32
Soldered Inkplate 5 Gen2
SolderedElectronics
130.6 × 75.2 mm258 parts2LTAPR-OHL-1.04ESP32
Soldered Inkplate 6COLOR
SolderedElectronics
131.4 × 105.5 mm177 parts2LTAPR-OHL-1.03ESP32
Soldered Inkplate 6 FLICK
SolderedElectronics
150.4 × 107.8 mm329 parts2LTAPR-OHL-1.02ESP32
Soldered Inkplate 6PLUS
SolderedElectronics
144.4 × 107.8 mm242 parts2LTAPR-OHL-1.02ESP32
Soldered Inkplate 6PLUS
SolderedElectronics
144.4 × 107.8 mm242 parts2LTAPR-OHL-1.01ESP32
Soldered Inkplate 5
SolderedElectronics
130.6 × 75.2 mm202 parts2LTAPR-OHL-1.00ESP32
Soldered-Inkplate-7-hardware design
SolderedElectronics
176.3 × 117.2 mm178 parts2LTAPR-OHL-1.00ESP32
Led controller
physiii
32 × 63 mm55 parts4LNo license0STM32
PGE
sKulll-J
85.5 × 66.8 mm51 parts2LNo license0AVR/Arduino
Main Board
jackwangxyw
75 × 45 mm32 parts4LCC-BY-NC-4.00- schematic only · 20 partsSTM32
AESH2026
iamanimeshshukl
20 partsNo license0 ESP8266
Wifi PB
AntonioMR
100 × 49.7 mm161 parts2LNo license29ESP32
Soldered Inkplate 10
SolderedElectronics
224.8 × 162.4 mm215 parts2LTAPR-OHL-1.018ESP32
Soldered Inkplate 4 TEMPERA with glass panel panel
SolderedElectronics
1.9 × 12 mm246 parts4LTAPR-OHL-1.05ESP32
Inkplate 6 SS panel
SolderedElectronics
294.8 × 119.8 mm223 parts2LTAPR-OHL-1.05ESP32
Soldered Inkplate 6 MOTION panel
SolderedElectronics
144.4 × 221.6 mm313 parts2LTAPR-OHL-1.04ESP32
Soldered Inkplate 5 Gen2 panel
SolderedElectronics
8.2 × 17.5 mm258 parts2LTAPR-OHL-1.04ESP32
Inkplate6COLOR Soldered panel
SolderedElectronics
268.8 × 117.5 mm176 parts2LTAPR-OHL-1.03ESP32
EMERALD
GemsErasmusPlus
90 × 40 mm68 parts2LCC-BY-SA-4.03ESP32
Soldered Inkplate 6 FLICK panel
SolderedElectronics
33.7 × 6.2 mm329 parts2LTAPR-OHL-1.02ESP32
Inkplate 6PLUS panel
SolderedElectronics
294.8 × 119.8 mm241 parts2LTAPR-OHL-1.02ESP32
Inkplate 6PLUS panel
SolderedElectronics
294.8 × 119.8 mm241 parts2LTAPR-OHL-1.01ESP32
Soldered Inkplate 5 panel
SolderedElectronics
267.2 × 162.5 mm202 parts2LTAPR-OHL-1.00ESP32
Inkplate10 Soldered panel
SolderedElectronics
224.8 × 174.4 mm214 parts2LTAPR-OHL-1.018ESP32
Soldered Inkplate 6FLICK Gen2
SolderedElectronics
144.4 × 107.8 mm247 parts2LTAPR-OHL-1.02Lipo charge mod
GJN-Aerospace
18 × 7 mm9 parts2LNo license0
How designs wire the MCP73831T
Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the MCP73831T connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a capacitor to GND on 13 of 19 designs, most often 100 nF (then 4.7 µF).
- The PROG pin has a resistor to GND on 13 of 19 designs, most often 2.49 kΩ (then 33 kΩ).
- The VBAT pin has a decoupling capacitor on 12 of 19 designs, most often 2.2 µF (then 4.7 µF).
- The VDD pin has a series resistor on 12 of 19 designs, most often 1 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 74% · a signal 26% | — |
| VBATpin 3 | Connected to: VBAT 68% · a signal 32% |
|
| VDDpin 4 | Connected to: CH340C 53% · VCC 26% |
|
| PROGpin 5 | Connected to: Signal 79% · not connected 21% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Makennbot by idlehandsdev, POV Fidget by idlehandsdev, Wifi PB by AntonioMR and Inkplate10 Soldered by SolderedElectronics.
The MCP73831T in open source designs
The gallery holds 33 open source boards using the MCP73831T from 20 GitHub repositories; a typical one measures about 137.9 × 106.7 mm and carries around 215 components.
88% are two-layer designs, the rest use four layers or more, and 73% carry an open source license.
The most starred is Makennbot by idlehandsdev.
Parts used alongside the MCP73831T
Microcontrollers on boards using the MCP73831T
What boards using the MCP73831T are built for
MCP73831T: common questions
Where can I find a MCP73831T reference design?
Each of the 33 boards on this page is a real design using the MCP73831T. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP73831T VDD pin connected?
The VDD pin has a capacitor to GND on 13 of 19 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 19 open source designs using the MCP73831T.
What resistor goes on the MCP73831T PROG pin?
The PROG pin has a resistor to GND on 13 of 19 designs, most often 2.49 kΩ (then 33 kΩ). Counted from the KiCad layouts of 19 open source designs using the MCP73831T.
What decoupling capacitors do designs use on the MCP73831T VBAT pin?
The VBAT pin has a decoupling capacitor on 12 of 19 designs, most often 2.2 µF (then 4.7 µF). Counted from the KiCad layouts of 19 open source designs using the MCP73831T.
What parts are used alongside the MCP73831T?
The CH340C, MC14093BDTR2G, PCAL6416AHF,128, TPS3840PL27DBVR and TPS7A2633DRVR appear in the most repositories here.
Which microcontrollers do boards using the MCP73831T use?
Most are built on ESP32 (25), ESP8266 (2), Microchip SAM (2) and STM32 (2).
How big is a typical board using the MCP73831T?
The median is 137.9 × 106.7 mm, and 88% are two-layer designs.
What is the most popular open source board using the MCP73831T?
By GitHub stars, Makennbot by idlehandsdev, with 175 stars.
Can I simulate one of these boards using the MCP73831T before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.