10 open source boards using the 74LS132
Real designs built with the 74LS132, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
EPSM-Famicom
Perkka2
99 × 91.7 mm59 parts4LCustom license76GSE14
stonedDiscord
163 × 249 mm102 parts2LBSD-2-Clause5Dragon32Rev3
jimbro1000
253 × 169.1 mm169 parts2LMIT3EPSM-Famicom rounded
Perkka2
99 × 91.7 mm59 parts4LCustom license76CPC464-2MINIDDI
Board-Folk
93.4 × 80.2 mm59 parts2LNo license10CPC-DDI20-OLD
Bread80
99.3 × 71 mm45 parts2LCERN-OHL-P-2.05GIMIX DMA Floppy
roberto314
248.9 × 139.7 mm124 parts2LBSD-2-Clause1- schematic only · 99 parts
TRS80 M2 CPU
trs80-net
99 parts2LNo license0 EPSM-Famicom blank
Perkka2
99 × 91.5 mm39 parts2LCustom license76CPC-DDI20
Bread80
99.1 × 65.9 mm38 parts2LCERN-OHL-P-2.05
How designs wire the 74LS132
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 74LS132 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF (then 100 pF).
- Pin 1 has a series resistor on 3 of 6 designs, most often 1 kΩ (then 160 Ω).
- Pin 2 has a series resistor on 3 of 6 designs, most often 1 kΩ (then 160 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 2 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 4 | Connected to: 74LS74 33% · not connected 17% |
|
| Pin 5 | Connected to: Signal 67% · not connected 33% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| Pin 12 | Connected to: A connector 33% |
|
| Pin 13 | Connected to: Signal 100% |
|
| VCCpin 14 | Connected to: 5V 100% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EPSM-Famicom by Perkka2, CPC464-2MINIDDI by Board-Folk, CPC-DDI20 by Bread80 and GSE14 by stonedDiscord.
The 74LS132 in open source designs
The gallery holds 10 open source boards using the 74LS132 from 7 GitHub repositories; a typical one measures about 99.1 × 91.7 mm and carries around 59 components.
80% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is EPSM-Famicom rounded by Perkka2.
Parts used alongside the 74LS132
What boards using the 74LS132 are built for
74LS132: common questions
Where can I find a 74LS132 reference design?
Each of the 10 boards on this page is a real design using the 74LS132. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 74LS132 VCC pin?
The VCC pin has a decoupling capacitor on 4 of 6 designs, most often 100 nF (then 100 pF). Counted from the KiCad layouts of 6 open source designs using the 74LS132.
What resistor goes on the 74LS132 pin 1?
Pin 1 has a series resistor on 3 of 6 designs, most often 1 kΩ (then 160 Ω). Counted from the KiCad layouts of 6 open source designs using the 74LS132.
What resistor goes on the 74LS132 pin 2?
Pin 2 has a series resistor on 3 of 6 designs, most often 1 kΩ (then 160 Ω). Counted from the KiCad layouts of 6 open source designs using the 74LS132.
What parts are used alongside the 74LS132?
The 74LS08, 74LS74, 74LS32, 74LS04 and 74LS123 appear in the most repositories here.
How big is a typical board using the 74LS132?
The median is 99.1 × 91.7 mm, and 80% are two-layer designs.
What is the most popular open source board using the 74LS132?
By GitHub stars, EPSM-Famicom rounded by Perkka2, with 76 stars.
Can I simulate one of these boards using the 74LS132 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.