26 open source boards using the 74LS123

Real designs built with the 74LS123, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

26 boardsClear filters|Most starred

How designs wire the 74LS123

Read from the KiCad layouts of 20 open source designs, one per repository: what each pin of the 74LS123 connects to, and the resistors, capacitors and other passives placed on it.

  • The RCEXT pins have a pull-up to 5V on 16 of 20 designs, most often 10 kΩ (then 100 kΩ).
  • The CLR pins is tied to 5V on 60% of them (GND on 3, a signal on 12).
  • The RCEXT pins have a capacitor to GND on 10 of 20 designs, most often 22 µF (then 10 µF).
  • The CEXT pins have a series capacitor on 9 of 20 designs, most often 100 µF (then 1 nF).
CLRpin 3, 11Connected to: 5V 60% · a signal 30%
CEXTpin 6, 14Connected to: GND 48% · a signal 43%
  • Series capacitor on 45% · 100 µF (4), 1 nF (3), 10 nF (2)
RCEXTpin 7, 15Connected to: Signal 85%
  • Pull-up to 5V on 80% · 10 kΩ (5), 100 kΩ (3), 4.7 kΩ (3)
  • Capacitor to GND on 50% · 22 µF (4), 10 µF (2), 2.2 nF (2)
  • Series capacitor on 35% · 1 nF (3), 10 nF (2), 15 pF (2)
GNDpin 8Connected to: GND 100%
VCCpin 16Connected to: 5V 100%
  • Decoupling capacitor on 35% · 100 nF (7)

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include St225 20427 by schlae, 128 X 16 RAM V4 FINAL by ibm2030, Coco9511pak by barberd and UMMF by nils-eilers.

The 74LS123 in open source designs

The gallery holds 26 open source boards using the 74LS123 from 21 GitHub repositories; a typical one measures about 137.4 × 115.3 mm and carries around 101 components.

81% are two-layer designs, the rest use four layers or more, and 35% carry an open source license.

The most starred is St251n 20603 by schlae.

Microcontrollers on boards using the 74LS123

74LS123: common questions

Where can I find a 74LS123 reference design?

Each of the 26 boards on this page is a real design using the 74LS123. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the 74LS123 RCEXT pin?

The RCEXT pins have a pull-up to 5V on 16 of 20 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 20 open source designs using the 74LS123.

How is the 74LS123 CLR pin connected?

The CLR pins is tied to 5V on 60% of them (GND on 3, a signal on 12). Counted from the KiCad layouts of 20 open source designs using the 74LS123.

How is the 74LS123 CEXT pin connected?

The CEXT pins have a series capacitor on 9 of 20 designs, most often 100 µF (then 1 nF). Counted from the KiCad layouts of 20 open source designs using the 74LS123.

What parts are used alongside the 74LS123?

The 74LS00, 74LS04, 74LS74, 74LS08 and 74LS32 appear in the most repositories here.

Which microcontrollers do boards using the 74LS123 use?

Most are built on AVR/Arduino (1).

How big is a typical board using the 74LS123?

The median is 137.4 × 115.3 mm, and 81% are two-layer designs.

What is the most popular open source board using the 74LS123?

By GitHub stars, St251n 20603 by schlae, with 38 stars.

Can I simulate one of these boards using the 74LS123 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part