7 open source boards using the C15999
Real designs built with the C15999, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Upico
dotcypress
36 × 77 mm59 parts6LApache-2.0134RP2040/RP2350
Rp gameboy cartridge hw
shilga
52.8 × 61.2 mm68 parts4LCERN-OHL-P-2.072ESP32
Ultisense
darshg321
44.7 × 93.6 mm83 parts2LNo license3STM32
Pdk prog
brainsmoke
42 × 37 mm56 parts2LCC-BY-4.01Esp ir receiver
valletw
33.1 × 21.5 mm46 parts4LMIT1Nordic nRF
Hyper7-Evo
ReFil
552.5 × 164.5 mm841 parts2LNo license0ESP32
DS8
bergamifer
100 × 100 mm71 parts2LNo license0
How designs wire the C15999
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the C15999 connects to, and the resistors, capacitors and other passives placed on it.
- The I/O1 pins have a series resistor on 4 of 7 designs, most often 27 Ω (then 0 Ω).
- The I/O2 pins have a series resistor on 4 of 7 designs, most often 27 Ω (then 0 Ω).
- The VBUS pin has a decoupling capacitor on 3 of 6 designs, most often 10 µF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| I/O1pin 1, 6 | Connected to: A connector 54% |
|
| GNDpin 2 | Connected to: GND 86% | — |
| I/O2pin 3, 4 | Connected to: A connector 54% |
|
| VBUSpin 5 | Connected to: VBUS 83% · a signal 17% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Upico by dotcypress, Rp gameboy cartridge hw by shilga, Ultisense by darshg321 and Pdk prog by brainsmoke.
The C15999 in open source designs
The gallery holds 7 open source boards using the C15999 from 7 GitHub repositories; a typical one measures about 44.7 × 77 mm and carries around 68 components.
57% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Upico by dotcypress.
Microcontrollers on boards using the C15999
What boards using the C15999 are built for
C15999: common questions
Where can I find a C15999 reference design?
Each of the 7 boards on this page is a real design using the C15999. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the C15999 I/O1 pin?
The I/O1 pins have a series resistor on 4 of 7 designs, most often 27 Ω (then 0 Ω). Counted from the KiCad layouts of 7 open source designs using the C15999.
What resistor goes on the C15999 I/O2 pin?
The I/O2 pins have a series resistor on 4 of 7 designs, most often 27 Ω (then 0 Ω). Counted from the KiCad layouts of 7 open source designs using the C15999.
What decoupling capacitors do designs use on the C15999 VBUS pin?
The VBUS pin has a decoupling capacitor on 3 of 6 designs, most often 10 µF (then 1 µF). Counted from the KiCad layouts of 7 open source designs using the C15999.
Which microcontrollers do boards using the C15999 use?
Most are built on ESP32 (2), RP2040/RP2350 (2), Nordic nRF (1) and STM32 (1).
How big is a typical board using the C15999?
The median is 44.7 × 77 mm, and 57% are two-layer designs.
What is the most popular open source board using the C15999?
By GitHub stars, Upico by dotcypress, with 134 stars.
Can I simulate one of these boards using the C15999 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.