18 open source boards using the CAT24C32
Real designs built with the CAT24C32, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Cognicity floodsensor
smart-facility
66 × 57 mm57 parts2LGPL-3.04Raspberry Pi
Chart plotter hat
gpgreen
65 × 56 mm68 parts4LNo license3Fablock
fablabcb
65 × 56 mm31 parts2LNo license2STM32
HW-Module-FMTransceiver
OE5XRX
100 × 100 mm68 parts4LCERN-OHL-S-2.01RP2040/RP2350
Rpi gpib pico
Elemecca
65 × 45 mm63 parts2LNo license1Calcifer
lowdrant
65 × 56 mm32 parts2LGPL-3.01Usb switchboard
irandms
65 × 30 mm31 parts2LNo license1Watson assistant
ibm-dev-incubator
65 × 56 mm45 parts4LCERN-OHL-1.20Telinfo pihat
seanpathayes
65 × 56 mm18 parts4LGPL-3.00RPi Hat SMD
CameronBrooks11
65 × 56.5 mm6 parts2LMIT0Raspberry Pi
Rpi rgb led matrix nonhat
jayeye
65 × 56 mm33 parts2LCustom license3Raspberry Pi GPIB µHAT
Elemecca
65 × 30 mm39 parts2LNo license1RPi Hat THT
CameronBrooks11
65 × 56 mm6 parts2LMIT0Raspberry Pi
Rpi rgb led matrix hat
jayeye
65 × 56 mm31 parts2LCustom license3Raspberry Pi
Rpi rgb led matrix hat centeredforprinting
jayeye
65 × 56 mm31 parts2LCustom license3EV Hat
pilotniq
65 × 56.5 mm37 parts2LNo license2AVR/Arduino
Pypilot tinypilot
pypilot
76.1 × 51.2 mm58 parts4LNo license3Zynth encoder power display fan
zynthian
65 × 56 mm34 parts2LNo license156
How designs wire the CAT24C32
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the CAT24C32 connects to, and the resistors, capacitors and other passives placed on it.
- The A0 pin is tied to GND on 14 of 14 designs.
- The A1 pin is tied to GND on 14 of 14 designs.
- The A2 pin is tied to GND on 14 of 14 designs.
- The SDA pin has a pull-up to 3.3V on 7 of 14 designs, most often 3.9 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 100% | — |
| A1pin 2 | Connected to: GND 100% | — |
| A2pin 3 | Connected to: GND 100% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: A connector 93% |
|
| SCLpin 6 | Connected to: A connector 93% |
|
| WPpin 7 | Connected to: A connector 50% |
|
| VCCpin 8 | Connected to: 3.3V 57% · a signal 43% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Zynth encoder power display fan by zynthian, Cognicity floodsensor by smart-facility, Chart plotter hat by gpgreen and Rpi rgb led matrix hat by jayeye.
The CAT24C32 in open source designs
The gallery holds 18 open source boards using the CAT24C32 from 14 GitHub repositories; a typical one measures about 65 × 56 mm and carries around 34 components.
72% are two-layer designs, the rest use four layers or more, and 39% carry an open source license.
The most starred is Zynth encoder power display fan by zynthian.
Parts used alongside the CAT24C32
Microcontrollers on boards using the CAT24C32
What boards using the CAT24C32 are built for
CAT24C32: common questions
Where can I find a CAT24C32 reference design?
Each of the 18 boards on this page is a real design using the CAT24C32. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the CAT24C32 A0 pin connected?
The A0 pin is tied to GND on 14 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the CAT24C32.
How is the CAT24C32 A1 pin connected?
The A1 pin is tied to GND on 14 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the CAT24C32.
How is the CAT24C32 A2 pin connected?
The A2 pin is tied to GND on 14 of 14 designs. Counted from the KiCad layouts of 14 open source designs using the CAT24C32.
Which microcontrollers do boards using the CAT24C32 use?
Most are built on Raspberry Pi (4), STM32 (2), AVR/Arduino (1) and RP2040/RP2350 (1).
How big is a typical board using the CAT24C32?
The median is 65 × 56 mm, and 72% are two-layer designs.
What is the most popular open source board using the CAT24C32?
By GitHub stars, Zynth encoder power display fan by zynthian, with 156 stars.
Can I simulate one of these boards using the CAT24C32 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.