21 open source boards using the CH224A

Real designs built with the CH224A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the CH224A

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the CH224A connects to, and the resistors, capacitors and other passives placed on it.

  • The CFG1 pin has a resistor to GND on 11 of 13 designs, most often 56 kΩ (then 120 kΩ).
  • The VHV pin has a decoupling capacitor on 9 of 13 designs, most often 1 µF (then 100 nF).
  • The VBUS pin has a decoupling capacitor on 6 of 13 designs, most often 1 µF (then 100 nF).
  • The PG pin has a pull-up to 3.3V on 6 of 13 designs, most often 10 kΩ (then 100 kΩ).
VHVpin 1Connected to: VBUS 85% · a signal 15%
  • Decoupling capacitor on 69% · 1 µF (8), 100 nF (4), 10 µF (1)
VBUSpin 8Connected to: VBUS 85% · a signal 15%
  • Decoupling capacitor on 46% · 1 µF (6), 100 nF (3)
CFG1pin 9Connected to: Signal 100%
  • Resistor to GND on 85% · 56 kΩ (4), 120 kΩ (3), 6.8 kΩ (2)
PGpin 10Connected to: Signal 85%
  • Pull-up to 3.3V on 46% · 10 kΩ (5), 100 kΩ (1)
  • Series resistor on 31% · 10 kΩ (2), 5.1 kΩ (1), 100 kΩ (1)
GNDpin 11Connected to: GND 100%

6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Thin laptop cm5-usb left by CopperPilot, PiEBV by Low-Boom, Pd12v6 by 0x63616c and USB C Power Supply by Chockalingam-M.

The CH224A in open source designs

The gallery holds 21 open source boards using the CH224A from 13 GitHub repositories; a typical one measures about 47.5 × 32 mm and carries around 49 components.

52% use four copper layers or more, and 29% carry an open source license.

The most starred is PiEBV by Low-Boom.

Parts used alongside the CH224A

Microcontrollers on boards using the CH224A

CH224A: common questions

Where can I find a CH224A reference design?

Each of the 21 boards on this page is a real design using the CH224A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the CH224A CFG1 pin?

The CFG1 pin has a resistor to GND on 11 of 13 designs, most often 56 kΩ (then 120 kΩ). Counted from the KiCad layouts of 13 open source designs using the CH224A.

What decoupling capacitors do designs use on the CH224A VHV pin?

The VHV pin has a decoupling capacitor on 9 of 13 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 13 open source designs using the CH224A.

What decoupling capacitors do designs use on the CH224A VBUS pin?

The VBUS pin has a decoupling capacitor on 6 of 13 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 13 open source designs using the CH224A.

Which microcontrollers do boards using the CH224A use?

Most are built on STM32 (3), ESP32 (2) and RP2040/RP2350 (1).

How big is a typical board using the CH224A?

The median is 47.5 × 32 mm, and 48% are two-layer designs.

What is the most popular open source board using the CH224A?

By GitHub stars, PiEBV by Low-Boom, with 1 stars.

Can I simulate one of these boards using the CH224A before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part