16 open source boards using the IP2721
Real designs built with the IP2721, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
QLAMP-main
hisashin
142 × 58 mm143 parts2LGPL-3.024STM32
PCB-reflow solder table
DerSpatz
100 × 100 mm77 parts2LMIT14- schematic only · 53 partsSTM32
Wmd6c servo
ChipCreates
53 partsMIT5 ESP32
Rc car
alaotach
129 × 79.8 mm85 parts4LNo license2IP2721-USB-C-breakout
louiscklaw
100 × 100 mm9 parts2LNo license2RP2040/RP2350
Spark
ratmuds
82 × 55 mm196 parts4LNo license1AVR/Arduino
2 679
wszeto9
101.6 × 95.3 mm122 parts2LNo license1STM32
Freyja gcs
aesirkth
300 × 200 mm281 parts4LNo license0STM32
Panelised PD+Display
Sitengwu
143.5 × 70 mm144 parts2LNo license0AVR/Arduino
Nixie Clock
PennyLekas
115 × 80 mm94 parts2LCERN-OHL-S-2.00Usb c to liion charger
MG-5
98 × 42 mm83 parts2LGPL-3.00ESP8266
Breakout boards
wszeto9
49 × 21.4 mm58 parts2LNo license0Usbpd adapter
fachat
61.3 × 45.5 mm49 parts2LNo license4ESP8266
Breakout boards panelized
wszeto9
100.1 × 91.7 mm55 parts2LNo license0USB PD
Sitengwu
41.5 × 50 mm23 parts2LNo license0Mini carte alim V2
evolutek
85 × 50 mm32 parts2LNo license0
How designs wire the IP2721
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the IP2721 connects to, and the resistors, capacitors and other passives placed on it.
- The CC2 pin has a resistor to GND on 12 of 13 designs, most often 5.1 kΩ.
- The CC1 pin has a resistor to GND on 12 of 13 designs, most often 5.1 kΩ.
- The TST2 pin is left unconnected on 13 of 13 designs.
- The TST3 pin is left unconnected on 13 of 13 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 2 | Connected to: VIN 54% · a signal 46% |
|
| NCpin 3, 4, 9, 10, 14, 15 | Connected to: Not connected 100% | — |
| GNDpin 5 | Connected to: GND 100% | — |
| TST1pin 6 | Connected to: Not connected 92% | — |
| TST2pin 7 | Connected to: Not connected 100% | — |
| TST3pin 8 | Connected to: Not connected 100% | — |
| SELpin 11 | Connected to: Signal 77% · not connected 23% |
|
| CC2pin 12 | Connected to: A connector 77% |
|
| CC1pin 13 | Connected to: A connector 77% |
|
| VBUSpin 16 | Connected to: 12V 38% · not connected 23% · a signal 38% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include QLAMP-main by hisashin, PCB-reflow solder table by DerSpatz, Usbpd adapter by fachat and Rc car by alaotach.
The IP2721 in open source designs
The gallery holds 16 open source boards using the IP2721 from 14 GitHub repositories; a typical one measures about 100 × 70 mm and carries around 80 components.
80% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.
The most starred is QLAMP-main by hisashin.
Parts used alongside the IP2721
Microcontrollers on boards using the IP2721
What boards using the IP2721 are built for
IP2721: common questions
Where can I find a IP2721 reference design?
Each of the 16 boards on this page is a real design using the IP2721. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the IP2721 CC2 pin?
The CC2 pin has a resistor to GND on 12 of 13 designs, most often 5.1 kΩ. Counted from the KiCad layouts of 13 open source designs using the IP2721.
What resistor goes on the IP2721 CC1 pin?
The CC1 pin has a resistor to GND on 12 of 13 designs, most often 5.1 kΩ. Counted from the KiCad layouts of 13 open source designs using the IP2721.
How is the IP2721 TST2 pin connected?
The TST2 pin is left unconnected on 13 of 13 designs. Counted from the KiCad layouts of 13 open source designs using the IP2721.
Which microcontrollers do boards using the IP2721 use?
Most are built on STM32 (4), AVR/Arduino (2), ESP32 (2) and ESP8266 (2).
How big is a typical board using the IP2721?
The median is 100 × 70 mm, and 80% are two-layer designs.
What is the most popular open source board using the IP2721?
By GitHub stars, QLAMP-main by hisashin, with 24 stars.
Can I simulate one of these boards using the IP2721 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.