6 open source boards using the LGS5145
Real designs built with the LGS5145, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Glider
Modos-Labs
90 × 80 mm356 parts4LCERN-OHL-S-2.02.7kRISC-V
Linkodrive08
jediminer543
67.2 × 90.4 mm144 parts4LApache-2.01STM32
Glider
pdyxs
90 × 80 mm356 parts4LCERN-OHL-S-2.00LGS5145 Voltage Regulator
R8bert
25 × 50 mm15 parts2LNo license0LGS5145 Voltage Regulator.sync conflict-20250314-135747-656VQ5O
R8bert
25 × 50 mm15 parts2LNo license0LGS5145 DCDC Converter Test Board
sdp8483
28.2 × 41.4 mm13 parts2LMIT0
How designs wire the LGS5145
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LGS5145 connects to, and the resistors, capacitors and other passives placed on it.
- The BST pin has a series capacitor on 5 of 5 designs, most often 100 nF.
- The FB pin has a resistor to GND on 5 of 5 designs, most often 240 kΩ (then 10 kΩ).
- The SW pin has a series capacitor on 5 of 5 designs, most often 100 nF.
- The SW pin has a inductor on 5 of 5 designs, most often 10 µH.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BSTpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 60% · a signal 40% |
|
| FBpin 3 | Connected to: Signal 100% |
|
| ENpin 4 | Connected to: Signal 100% |
|
| VINpin 5 | Connected to: 5V 80% · a signal 20% |
|
| SWpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Glider by Modos-Labs, Linkodrive08 by jediminer543, Glider by pdyxs and LGS5145 Voltage Regulator by R8bert.
The LGS5145 in open source designs
The gallery holds 6 open source boards using the LGS5145 from 5 GitHub repositories; a typical one measures about 47.7 × 65 mm and carries around 80 components.
50% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is Glider by Modos-Labs.
Parts used alongside the LGS5145
What boards using the LGS5145 are built for
LGS5145: common questions
Where can I find a LGS5145 reference design?
Each of the 6 boards on this page is a real design using the LGS5145. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LGS5145 BST pin connected?
The BST pin has a series capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the LGS5145.
What resistor goes on the LGS5145 FB pin?
The FB pin has a resistor to GND on 5 of 5 designs, most often 240 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the LGS5145.
How is the LGS5145 SW pin connected?
The SW pin has a series capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the LGS5145.
What parts are used alongside the LGS5145?
The ADV7611, CBTL02043A, FUSB302BMPX, INA3221 and JW3651QFNE appear in the most repositories here.
Which microcontrollers do boards using the LGS5145 use?
Most are built on STM32 (2) and RISC-V (1).
How big is a typical board using the LGS5145?
The median is 47.7 × 65 mm, and 50% are two-layer designs.
What is the most popular open source board using the LGS5145?
By GitHub stars, Glider by Modos-Labs, with 2,676 stars.
Can I simulate one of these boards using the LGS5145 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.